Stiga ST 526 S Gebrauchsanweisung Seite 110

WARNING!: READ THIS MANUAL CAREFULLY BEFORE
EN
USING THE MACHINE. Keep safe for future use.
INDICE
1. GENERAL INFORMATION ........................... 1
2. SAFETY REGULATIONS .............................. 2
2.4 Maintenance, storage and transport...... 3
3. ABOUT THE MACHINE ................................ 4
3.1 Machine description and intended use.. 4
3.2 Safety signs .......................................... 4
3.3 Identification label ................................ 5
3.4 Main components ................................. 5
4. ASSEMBLY ................................................... 5
4.1 Assembly components .......................... 5
4.2 Mounting the forward control and auger
cables ................................................... 6
4.3 Handle assembly .................................. 6
4.4 Gear lever assembly ............................. 6
4.5 Discharge chute assembly .................... 6
4.6 Mounting the auger extension (ST 767 H)
.............................................................. 6
4.7 Levelling shoes ..................................... 6
5. CONTROLS.................................................. 7
5.1 Ignition key ............................................ 7
5.2 Fuel tap ................................................. 7
5.3 Throttle command ................................. 7
5.4 Choke command ................................... 7
5.5 Primer ................................................... 7
5.6 Manual starting grip .............................. 7
5.7 Electrical start command ....................... 7
5.8 Forward control ..................................... 7
5.9 Steering lever ........................................ 7
5.10 Auger control ......................................... 8
5.11 Gear lever ............................................. 8
5.12 Chute and deflector guiding (version with
handle) .................................................. 8
5.13 Chute and deflector electrical guiding
(version with buttons) ............................ 8
5.14 Headlights and grip heating switches
(optionals) ............................................. 8
5.15 Lifting pedal .......................................... 8
6. USING THE MACHINE ................................. 8
6.1 Preliminary operations .......................... 9
6.2 Safety checks ........................................ 9
6.3 Starting / operation ................................ 9
6.4 Stop .................................................... 10
6.5 Operating suggestions ........................ 11
6.6 After use .............................................. 11
7. MAINTENANCE ......................................... 11
7.1 General Information ............................ 11
7.2 Refuelling ............................................ 11
7.3 Check/top-up engine oil ...................... 12
7.4 Cleaning .............................................. 12
7.5 Spark plug ........................................... 12
7.6 Carburettor .......................................... 12
7.7 Nuts and bolts ..................................... 13
7.8 Auger shaft .......................................... 13
8. STORAGE .................................................. 13
9. ASSISTANCE AND REPAIRS ..................... 13
10. WARRANTY COVERAGE .......................... 13
11. MAINTENANCE TABLE .............................. 14
12. TROUBLESHOOTING ............................... 15
1. GENERAL INFORMATION
1.1 HOW TO READ THIS MANUAL
Some of the paragraphs in this manual contain
particularly important information in terms
of safety and operation, and are highlighted
differently, according to the following criteria:
NOTE or IMPORTANT These give details
or further information on what has been
previously indicated and aim to prevent damage
to the machine or cause other damage.
The symbol represents a danger. Failure
to observe the warning can lead to possible
personal and/or third party injury and/or damage.
The paragraphs highlighted in a dotted grey
square indicate optional characteristics
not available on all models documented
in this manual. Check if the characteristics
are available on this model.
Whenever reference is made to a position on the
machine "front", "back", "left" or "right" hand side,
this refers to the operator's working position.
1.2 REFERENCES
1.2.1 Figures
The figures in these instructions for
use are numbered 1, 2, 3, etc.
Components shown in the figures
are marked A, B, C, etc.
Reference to component C in figure
2 is indicated with the wording: "See
fig. 2.C" or simply "(Fig. 2.C)".
The figures are provided by way of
example. The actual pieces can differ from
those illustrated in this document.
EN - 1