Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
16 | English
Fitting the Abrasive Tools (see figure A)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Only use open-ended spanners that are suitable and
u
undamaged (see "Technical Data").
– Clean the grinding spindle (3) and all the parts to be fit-
ted.
– Use an open-ended spanner (9) on the spanner flat of the
grinder spindle (3) to hold it in place.
Loosen the clamping nut (2) by placing an open-ended
spanner (10) on the spanner flat and turning it counter-
clockwise.
– Insert the straight shank of the grinding tool all the way
into the collet (1).
– Hold the grinding spindle (3) with the open-ended span-
ner (9) and tighten the application tool by placing the
open-ended spanner (10) on the spanner flat and turning
it clockwise.
The grinding tools must run completely concentrically. Do
not continue to use damaged grinding tools that are out of
balance. If the grinding tools are out of balance, they should
be replaced.
Do not, under any circumstances, tighten the collet
u
with the clamping nut until a grinding tool has been
fitted. The collet may otherwise become damaged.
Only use mounted points with an appropriate shank
u
diameter. A mounting point with a shank diameter which
does not correspond to the tool holder of the power tool
(see "Technical data") cannot be held properly and will
damage the collet chuck.
The application tool must be clamped at least 10 mm.
u
The inner shank dimension L
0
maximum permitted speed of the application tool from
the specifications provided by the manufacturer of the
application tool. It must not be less than the maximum
speed of the power tool.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
1 609 92A 6YL | (02.12.2021)
can be used to calculate the
Operation
Starting operation
Switching On and Off
To start the power tool, slide the on/off switch (5) forwards.
To lock the on/off switch (5) in position, push the on/off
switch (5) forwards and down until it clicks into place.
To switch off the power tool, release the on/off switch (5);
or, if the switch is locked, briefly push the on/off switch (5)
backwards and down and then release it.
Restart Protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (5) to the off posi-
tion and then switch the power tool on again.
Note: Rapidly switching the power tool off and on again may
trigger the restart protection, meaning the power tool may
not start up even if the on/off switch (5) is pressed. Set the
on/off switch (5) to the off position and then switch the
power tool on again.
Practical advice
Move the grinding tool evenly back and forth with light pres-
sure to achieve an optimum work result. Pressure that is too
strong reduces the performance capability of the power tool
and causes the grinding tool to wear more quickly.
Protect the grinding tools against impact.
u
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Bosch Power Tools
Werbung
Inhaltsverzeichnis
