EINHELL GE-GS 18 Li-Solo Originalbetriebsanleitung Seite 16

should return to its starting position. If this fails to
happen, try turning the ring (B) by hand into its
starting position.
Now pull on the blade to check whether it is tightly
seated in the holder.
5.2 Fitting the branch jaw clamp (Fig. 3b/3c)
The branch jaw clamp (Fig. 1/Item 5) helps you to
guide the equipment when cutting branches. The
equipment can be used either with or without the
branch jaw clamp.
To fi t the branch jaw clamp, press the lock release
(Fig. 3b/Item A) and push the branch jaw clamp
onto the soleplate from above. Make sure that the
two pins (Fig. 3c/Item A) are correctly seated in
the related recesses (Fig. 3c/Item B) of the so-
leplate. Then check that the branch jaw clamp is
securely seated.
5.3 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (A) from the handle,
pressing the pushlock button (B) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(C) into the socket outlet. The green LED will
then begin to blink.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit.
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
Anl_GE_GS_18_Li_SPK13.indb 16 Anl_GE_GS_18_Li_SPK13.indb 16
GB
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.4 Battery capacity indicator (Fig. 4/Item D)
Press the button for the battery capacity indicator
(E). The battery capacity indicator (D) will indicate
the charge status of the battery by means of 3
LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
6.1 On/Off switch (Fig. 1/Item 1)
Switching on:
Press the locking button (2) and the On/Off switch
(1).
Infi nitely variable stroke speed control is possible
with the On/Off switch (1). The further you push
the switch, the higher the stroke speed.
Switching off :
Release the locking button (2) and the ON/OFF
switch (1) at the same time.
- 16 -
25.04.2022 11:20:14 25.04.2022 11:20:14