Maintenance And Service - Bosch GSB 13 RE Professional Originalbetriebsanleitug

14 | English
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Setting the Rotational Direction (see figures G–H)
The rotational direction switch (8) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (6) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (8) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (8) through to the right
stop.
Setting the Operating Mode
Drilling and screwdriving
Set the selector switch (4) to the "drilling"
symbol.
Impact drilling
Set the selector switch (4) to the "impact
drilling" symbol.
The selector switch (4) clicks into place and
can also be actuated when the motor is running.
Switching on/off
To start the power tool, press and hold the on/off switch
(6).
Press the lock-on button (5) to lock the on/off switch (6) in
this position.
To switch off the power tool, release the on/off switch (6);
or, if the switch is locked with the lock-on button (5), briefly
press the on/off switch (6) and then release it.
Adjusting the Speed/Impact Rate
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (6) to varying extents.
A light pressure on the on/off switch (6) results in a low rota-
tional speed. Increased pressure on the switch causes an in-
crease in speed.
Preselecting the Speed/Impact Rate (not applicable to
tool model 3 601 B17 103)
You can preselect the required speed/impact rate using the
speed preselection thumbwheel (7), even during operation.
The required speed/impact rate is dependent on the mater-
ial and the work conditions and can be determined by prac-
tical trials.
Practical Advice
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Only apply the power tool to the screw/nut when the
u
tool is switched off. Rotating tool inserts can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
1 609 92A 53D | (12.07.2019)
To drill into tiles, set the selector switch (4) to the "drilling"
symbol. After drilling through the tile, set the selector switch
to the "impact drilling" symbol and drill with impact.
Use carbide drill bits when working with concrete, stone and
masonry.
When drilling into metal, only use sharpened HSS drills (HSS
= high-speed steel) which are in perfect condition. The
Bosch accessory range guarantees appropriate quality.
Using the drill bit sharpener (accessory), you can effortlessly
sharpen twist drill bits with a diameter of 2.5–10 mm.

Maintenance and Service

Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Autogoods "130"
Bosch Power Tools