Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
1. GENERAL
1.1 Carefully read the following important
information regarding installation safety and
maintenance. Keep this information booklet
accessible for further consultations.
The appliance has been designed as a suction
version (external exhaust) or as a filter version
(internal air recycle) cooker hood.
2. INSTALLATION INSTRUCTIONS
2.1 Electric Connection
The appliance has been manufactured as a class
II, therefore no earth cable is necessary.
The connection to the mains is carried out as
follows:
BROWN
BLUE
If not provided, connect a plug for the electrical
load indicated on the description label. Where a
plug is provided, the cooker hood must be installed
in order that the plug is easily accessible.
An omnipolar switch with a minimum aperture of
3mm between contacts, in line with the electrical
load and local standards, must be placed between
the appliance and the network in the case of direct
connection to the electrical network.
2.2 The appliance must be installed at a
minimum height of 650 mm from an electric
cooker stove, or 750 mm from gas or
combined cooker stoves.
If a connection tube composed of two parts
is used, the upper part must be placed
outside the lower part.
Do not connect the cooker hood exhaust to
the same conductor used to circulate hot air
or for evacuating fumes from other
appliances generated by other than an
electrical source.
2.3 Mounting the cooker hood to the wall
Drill holes A-B-C-D according to indications
quoted in (fig. 3).
Use screws and screw anchors suitable for wall
(e.g. reinforced cement, plasterboard) for the
mounting of the cooker hood.
Where screws and screw anchors are supplied
ensure that they are suitable for the type of wall
where the cooker hood is to be mounted.
Lock in the flange connector Y to the cooker hood
(fig. 2).
Downloaded from
www.Manualslib.com
= L line
= N neutral
manuals search engine
Affix the bracket Z to the wall via the drill holes A
(fig.4).
Hang the cooker hood on the wall using the drill
holes C (fig.3).
Fasten the cooker hood using the fastening drill
holes D (fig.3).
2.4 Suction Version
Connect the flange Y to the discharge opening
with a connecting tube (do not carry out for filter
version).
Thread the upper connector E to the inside of the
lower connector F; hang the two connectors
inserting them vertically on the cooker hood
locking the lower connector F to the wall using
the drill holes B (fig. 3), unthread the upper
connector E towards the top, locking it in with the
appropriate screws in the drill holes G of the
bracket Z (fig. 2) previously affixed to the wall via
the drill holes A (fig. 3).
In order to transform your cooker hood from
suction version to filter version, ask your local
retailer for active carbon filters and then carry
out instructions for mounting filter version cooker
hood.
2.5 Filter Version
Install the cooker hood and the two connectors
as described in the paragraph mounting the
suction version cooker hood.
To mount the filter connector refer to instructions
included in the kit.
If the kit is not supplied, then order the kit as an
accessory from your local dealer.
The filters must be applied to the suction kit
located inside the cooker hood and centred by
rotating at 90 degrees until locked in.
The air is replaced in the environment via the
eyelets impressed on the connector E.
3. USE AND MAINTENANCE
3.1 It is recommended to operate the appliance
prior to cooking.
It is recommended to leave the appliance in
operation for 15 minutes after cooking is
terminated in order to completely eliminate
cooking vapours and odours.
The proper function of the cooker hood is
conditioned by the regularity of the maintenance
operations, in particular, the active carbon filter.
3.2 The anti-grease filters capture the grease
particles suspended in the air, and are therefore
subject to clogging according to the frequency of
the use of the appliance.
6
Werbung
Inhaltsverzeichnis
