Specifications; Additional Safety Rules For Tool - Makita 8270d Betriebsanleitung

ENGLISH
1 Button
2 Battery cartridge
3 Switch trigger
4 Reversing switch lever
5 Low speed
6 High speed

SPECIFICATIONS

Model
Capacities
Steel .............................................................10 mm
Wood ............................................................25 mm
Concrete.......................................................8 mm
Wood screw..................................................5.1 mm x 63 mm
Machine screw .............................................6 mm
-1
No load speed (min )
High ..............................................................0 – 1,200
Low...............................................................0 – 350
Blows per minute
High .............................................................0 – 18,000
Low ..............................................................0 – 5,250
Overall length ..................................................214 mm
Net weight .......................................................1.6 kg
Rated voltage ..................................................D. C. 12 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for impact drilling in brick, concrete
and stone as well as for drilling without impact in wood,
metal, ceramic and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
4
Explanation of general view
7 Speed change lever
8 Action mode changing ring
9 Arrow
10 Graduations
11 Adjusting ring
12 Sleeve
8270D
7.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
ENC004-1
2.
3.
4.

ADDITIONAL SAFETY RULES FOR TOOL

1.
2.
13 Ring
14 Tighten
15 Blow-out bulb
8280D
10 mm
25 mm
10 mm
5.1 mm x 63 mm
6 mm
0 – 1,200
0 – 350
0 – 18,000
0 – 5,250
214 mm
1.7 kg
D. C. 14.4 V
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Wear ear protectors with impact drills. Exposure
to noise can cause hearing loss.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
8390D
13 mm
36 mm
13 mm
6 mm x 75 mm
6 mm
0 – 1,200
0 – 350
0 – 18,000
0 – 5,250
239 mm
2.3 kg
D. C. 18 V
ENB002-2