Tekniske Specifikationer; Additional Safety Instructions - Ferm CDM1049 Gebrauchsanweisung

UK
2. SAFETY INSTRUCTIONS
The following symbols are used in these instructions for use:
In accordance with essential applicable safety standards of European directives
The charging adapter is double insulated in
accordance with EN-60335; therefore no earth wire is required.
Denotes risk of personal injury, loss of life or damage to the tool in case of non-
observance of the instructions in this manual.
Indicates electrical shock hazard.
Read instructions carefully
Indoor use only
In case of failure, the transformer is not dangerous
Thermic protector
Faulty and/or discarded electrical or electronic apparatus have to be collected at the
appropriate recycling locations.

ADDITIONAL SAFETY INSTRUCTIONS

1. Only use the accumulator block with the battery charger provided – using other chargers
could be dangerous.
2. Keep the accumulator block, tool and battery charger away from damp and wet
conditions.
3. Before using the battery charger, check all wires are properly connected.
4. If any wires on the charger are damaged, do not use it until these have been replaced.
5. When the charger is not in use it should not be plugged in. When unplugging, do not pull
the plug out by the cable.
6. If the charger breaks down or suffers from other technical problems, take it to a
recognised dealership to be checked before using it again. Any damaged parts must be
replaced.
7. Take care when handling the accumulator block, do not drop it or knock it against other
things.
8. Never attempt to repair the battery charger or accumulator block yourself; this can be
extremely dangerous. Repairs should always be carried out by a
recognised dealership.
9. Always unplug the charger before cleaning or carrying out any other maintenance on it.
6
LEDNINGSFRI SKRUETRÆKKER FCS-360LK
Læs denne brugervejledning godt igennem, før du tager maskinen i brug. Sørg for, at
du har kendskab til, hvordan maskinen fungerer, og hvordan den skal betjenes.
Vedligehold maskinen ifølge instruktionerne, så den altid fungerer optimalt.
Opbevar denne brugervejledning og den vedlagte dokumentation sammen med maskinen.
NUMRENE I DEN FØLGENDE TEKST HENVISER TIL ILLUSTRATIONERNE PÅ SIDE 2-4
Indledning
Denne skruetrækker er tilsigtet stramning og frigørelse af skruer (fig. 2 - 6).
Indhold:
1.

Tekniske specifikationer

2. Sikkerhedsinstruktioner
3. Montering af tilbehør
4. Drift
5. Opladning af batteriet
6. Vedligeholdelse
1. TEKNISKE SPECIFIKATIONER
Pakken indeholder
1 Accu skruetrækker
1 Oplader
1 Magnetisk bitholder
8 Tilbehør
1 Brugsanvisning
1 Sikkerhedsinstruktioner
1 Garantibevis
Kontroller maskinen, løse dele og tilbehør for transportskade.
Tekniske specifikationer
Oplader
Frekvens
Batterikapacitet
Opladningstid
Maks. drejningsmoment
Ubelastet hastighed
Vægt
LPA
LWA
Vibration
KOMPONENTER
Fig. 1
1. Holder
2. Afbryderknap
3. Blødt greb
4. LED (indikationslampe)
5. Opladningsforbindelse
6. Forlængerdel
7. Tilbehør
Ferm Ferm
DK
| 3,6 V / 600 mA
| 50 Hz
| 1,1 Ah
| < 5 timer
| 3.0 Nm
| 230 r/min
| 340 gr.
| 58.1 dB(A)
| 69.1 dB(A)
| < 2,5 m/s 2
55