Peavey TransTube 100 EFX Handbuch Seite 7

R R e e a a r r P P a a n n e e l l
27 26
CAUTION
120V
60 Hz
WARNING:
TO REDUCE THE RISK OF FIRE OR
300 WATTS
ELECTRIC SHOCK DO NOT EXPOSE THIS EQUIPMENT
GND.
TO RAIN OR MOISTURE.
AVIS:
RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
0
Keep out
Serial
Sticker area
( ( 1 1 6 6 ) ) R R E E M M O O T T E E S S W W I I T T C C H H
This eight-pin DIN connector is provided for connection of the PFC 3 footswitch (included). The
footswitch cable should be connected before the amp is powered up. See the FOOTSWITCH
section of this manual for explanation of footswitch operation.
( ( 1 1 7 7 ) ) E E F F F F E E C C T T S S L L E E V V E E L L S S W W I I T T C C H H
Selects the effects loop operating level: -10 dBV (0.3V RMS) when "out" and 0 dBV (1 V RMS)
when "in".
( ( 1 1 8 8 ) ) E E F F F F E E C C T T S S S S E E N N D D
Output for supplying signals to external low-level effects or signal processing equipment.
( ( 1 1 9 9 ) ) E E F F F F E E C C T T S S R R E E T T U U R R N N
Input for returning signals from external low-level effects or signal processing equipment.
( ( 2 2 0 0 ) ) P P R R E E A A M M P P O O U U T T
The preamp out can be used to route the amplified signal from the preamp to a mixing console,
tape recorder, etc. Connect the preamp output to line-level inputs of other equipment using high
quality shielded cable. This patch does not affect operation of the amplifier.
( ( 2 2 1 1 ) ) P P O O W W E E R R A A M M P P I I N N
Used to connect line-level signals to the power amplifier section. Connect the power amp input to
line-level output of other equipment using high quality shielded cable. This patch disconnects the
preamp section from the power amp section.
( ( 2 2 2 2 ) ) D D A A M M P P I I N N G G
This three-position switch allows for adjustment of the damping factor of the power amplifier.
Damping is the ability of an amplifier to control speaker cone motion after the signal disappears.
A higher damping factor (TIGHT) reduces cone vibration more quickly than a lower damping factor
(LOOSE). This switch works much like the Resonance and Presence controls found on other
Peavey amps, if they were to be turned simultaneously. If the Damping switch is changed, the
volume level of the amp will also change and may require re-adjustment of the volume.
( ( 2 2 3 3 ) ) P P O O W W E E R R
This three-position switch selects the power output level of the power amplifier. This switch
works like the T. Dynamics
pronounced tube power compression simulation at lower settings.
22
DAMPING
LOOSE MEDIUM TIGHT
POWER
100W 50W 25W
REMOTE
SPEAKER OUTPUTS
SWITCH
100 WATTS RMS/40V RMS, 4 OHMS MIN.
SPEAKER JACKS PARALLELED
16 16 23
® control found on other Peavey amplifiers which provides for a more
24
IMPEDANCE SELECTOR
16 8 4
25
7
21 18
R
TRANSTUBE 1 00 EFX HD
PWR AMP PRE AMP EFX EFX EFX
IN OUT RETURN SEND LEVEL
-10 dBV (.3V RMS)
20 19 17
0 dBV (1V RMS)