Herunterladen Inhalt Inhalt Diese Seite drucken

Accessories - Black & Decker KR70LSR Handbuch

Vorschau ausblenden Andere Handbücher für KR70LSR:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 6
ENGLISH
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Lock-on button
3. Forward/reverse slider
4. Drilling mode selector
5. Side handle
6. Chuck
7. Bit storage
8. Latch
9. Laser unit
10. Wall mount
Assembly
Warning! Make sure that the tool is switched off and
unplugged.
Fitting the side handle (fig. A)
Screw the side handle (5) into the one of the holes (11) on
x
either side of the tool.
Fitting a drill bit or screwdriver bit (fig. B)
Open the chuck by turning the front part (13) with one
x
hand while holding the rear part (12) with the other.
Insert the bit shaft (14) into the chuck and firmly tighten
x
the chuck.
Removing and refitting the chuck (fig. C)
Open the chuck as far as possible.
x
Remove the chuck retaining screw, located in the front part
x
of the chuck, by turning it clockwise using a screwdriver.
Tighten an Allen key (15) into the chuck and strike it with
x
a hammer as shown.
Remove the Allen key.
x
Remove the chuck by turning it counterclockwise.
x
To refit the chuck, screw it onto the spindle and secure it
x
with the chuck retaining screw.
Removing and replacing the laser unit
The tool provides a mounting location where the laser unit (9)
is stored when not in use.
To remove the unit, release the latch (8) by pressing it
x
downward and slide the unit out of the mounting location.
To replace the unit, release the latch (8) and slide the unit
x
into the mounting location.
4
Removing and replacing the wall mount
To remove the wall mount (10), rotate the collar counter-
x
clockwise until the wall mount comes off the tool.
To replace the wall mount (10), place the wall mount with
x
the legs closed in the hole in the bottom of the tool and
rotate the collar clockwise until the wall mount engages.
Use
Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse
x
slider (3) to the left.
To select reverse rotation, push the forward/reverse slider
x
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode
For drilling in masonry, set the drilling mode selector (4) to
x
the
position.
For drilling in other materials and for screwdriving, set the
x
drilling mode selector (4) to the
Switching on and off
To switch the tool on, press the variable speed switch (1).
x
The tool speed depends on how far you press the switch.
As a general rule, use low speeds for large diameter drill
bits and high speeds for smaller diameter drill bits.
For continuous operation, press the lock-on button (2) and
x
release the variable speed switch. This option is available
only at full speed.
To switch the tool off, release the variable speed switch.
x
To switch the tool off when in continuous operation,
press the variable speed switch once more and release it.
Using the laser unit
The laser unit (9) is used for the alignment of several drill holes.
Remove the unit from the tool.
x
Refer to the manual of the laser unit for further instructions.
x

Accessories

The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
position.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis