Optional Accessories - Makita UH5580 Bedienungsanleitung

NOTICE:
If the parts other than the shear blades
such as the crank are worn out, ask Makita
Authorized Service Centers for parts replacement
or repairs.
Removing or installing shear blade
CAUTION:
• Before removing or installing shear blade, always
be sure that the tool is switched off and unplugged.
• When replacing the shear blade, always wear
gloves without removing blade cover so that
hands and face does not directly contact the
blade. Failure to do so may cause personal injury.
NOTE:
• Do not wipe off grease from the gear and crank.
Failure to do so may cause damage to the tool.
• For specific way of removing and installing
shear blades refer to the reverse of a package
for accessory shear blades.
Removing the shear blades
Reverse the tool and loosen four screws.
► Fig.20: 1. Screws 2. Blade cover
NOTE:
• Be careful not to get your hands dirty as grease
is applied in the shear blade driving area.
Remove the under cover.
► Fig.21: 1. Under cover 2. Blade cover
Remove the gear housing cover.
► Fig.22: 1. Gear housing cover
Set the crank at the angle as shown in the figure with a
slotted bit screwdriver.
► Fig.23: 1. Crank
Remove two screws from the shear blades and the
shear blade unit will be taken out.
► Fig.24: 1. Screws 2. Shear blade
CAUTION:
• Return the gear to the original position in such
a manner as it was installed if it should be taken
away by mistake.
Installing the shear blade
Prepare 4 removed screws (For under cover), 2 screws
(For shear blade), gear housing cover, under cover, and
new shear blades.
Adjust the crank position as shown in the figure. At
this time, apply some grease provided with new shear
blades to the periphery of the crank.
► Fig.25: 1. Crank
Overlap the oval hole in the upper blade with that in the
lower one.
► Fig.26: 1. Ellipse of shear blade
Take out the blade cover from the old shear blades and
fit it onto the new ones for easy handling during the
replacement of blades.
► Fig.27
Place the new shear blades on the tool so that the oval
holes in the shear blades fit onto the crank. Overlap the
holes in the shear blades with the screw holes in the
tool and then secure them with two screws.
► Fig.28: 1. Ellipse of shear blade 2. Crank
Check the crank for smooth turn with a slotted bit
screwdriver.
► Fig.29: 1. Crank
Install the gear housing, under cover on the tool.
Tighten the screw firmly.
Remove the blade cover and then turn on the tool to
check it for proper movement.
NOTE:
• When the shear blades does not operate prop-
erly, there is a poor fit between the blades and
crank. Redo from the beginning.
Storage
The hook hole in the bottom of the blade cover is con-
venient for hanging the tool from a nail or screw on the
wall.
► Fig.30
Put the blade cover on the shear blades so that the
blades are not exposed. Store the tool out of the reach
of children carefully.
Store the tool in the place not exposed to water and
rain.
To maintain product SAFETY and RELIABILITY,
repairs, carbon brush inspection and replacement, any
other maintenance or adjustment should be performed
by Makita Authorized Service Centers, always using
Makita replacement parts.
OPTIONAL
ACCESSORIES
CAUTION:
• These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Blade cover
• Hook complete
• Shear blade assembly
• Waist cord hook
• Arm cord hook
NOTE:
• Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
10 ENGLISH