Herunterladen Inhalt Inhalt Diese Seite drucken

Remote Controller Check - Mitsubishi Electric PAR-30MAA Installationsanleitung

Vorschau ausblenden Andere Handbücher für PAR-30MAA:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

[Resetting the error history]
[1] Press the F4 button (Reset) on
the screen that shows the error
history. A confirmation screen
will appear asking if you want to
delete the error history.
(7) Setting the maintenance password
Take the following steps to change the maintenance password.
[Procedures]
[1] Select "Maintenance password" on the Service menu, and press the SELECT button to bring up
the screen to enter a new password.
[2] Move the cursor to the digit you want to change with the F1 or F2 button, and set each digit to the
desired number (0 through 9) with the F3 or F4 button.
[3] Press the SELECT button to save the new password.
[4] A confirmation screen will appear asking if you want to change the maintenance password. Press
the F4 button (OK) to save the change. Press the F3 button (Cancel) to cancel the change.
[5] "Changes saved" will appear when the password is updated.
[6] Press the MENU button to return to the Service menu or press the RETURN button to go back to
the "Maintenance password" screen.

13. Remote controller check

When the remote controller does not work properly, use the remote controller checking function to troubleshoot the problem.
(1) Check the remote controller display and see if anything is displayed (including lines). Nothing will appear on the remote controller
display if the correct voltage (8.5-12 VDC) is not supplied to the remote controller. If this is the case, check the remote controller wiring
and indoor units.
[Procedures]
[1] Select "Remote controller check" from the Service menu, and press the SELECT button to start the remote controller check and see
the check results. To cancel the remote controller check and exit the Remote controller check menu screen, press the MENU or the
RETURN button. The remote controller will not reboot itself.
Service menu
Maintenance password
Remote controller check
Main menu:
Cursor
Select "Remote controller check".
OK: No problems are found with the remote controller. Check other parts for problems.
E3, 6832: There is noise on the transmission line, or the indoor unit or another remote controller is faulty. Check the transmission line and
the other remote controllers.
NG (ALL0, ALL1): Send-receive circuit fault. Remote controller needs replacing.
ERC: The number of data errors is the discrepancy between the number of bits in the data transmitted from the remote controller and that
of the data that was actually transmitted over the transmission line. If data errors are found, check the transmission line for external
noise interference.
[2] If the SELECT button is pressed after the remote controller check results are displayed, remote controller check will end, and the
remote controller will automatically reboot itself.
Self check
Ref. address
Delete error history?
Cancel
OK
Remote controller check
Start checking?
Begin:
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Authorized representative in EU: MITSUBISHI ELECTRIC EUROPE B.V.
HARMAN HOUSE, 1 GEORGE STAREET, UXBRIDGE, MIDDLESEX UB8 1QQ, U.K.
[2] Press the F4 button (OK) to
delete the error history. If
deletion fails, "Request rejected"
will appear, and "Unit not exist"
will appear if no indoor units that
are correspond to the entered
address are found.
Remote controller check
Exit:
Remote controller check results screen
– 16 –
Self check
Ref. address
Error history deleted
Return:
Maintenance password
Enter maintenance password
Change maintenance password.
Select:
Cursor
Maintenance password
Enter maintenance password
Update maintenance password?
Cancel
OK
Maintenance password
Enter maintenance password
Changes saved
Service menu:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis