Mebus 10389 Bedienungsanleitung Seite 16

MAIN FEATURES: REMOTE UNIT
WIRELESS THERMO • HYGRO
1
A C
A LED INDICATOR
Flashes once when the remote unit transmits a
reading. Flashes twice when low battery is detected
on sensor unit
B BATTERY COMPARTMENT
Accommodates two AA-size batteries
C RESET BUTTON
Press to reset all setting if you have selected
different channel.
D CHANNEL SELECTOR
Select the channel before you install batteries.
E WALL-MOUNT RECESSED HOLE
Supports the remote until in wall-mounting
F ˚C/ ˚F BUTTON
54
HOW TO USE THE TABLE STAND
OR WALL MOUNTING
The main unit has a removable table stand, which when
connected, can support the unit on a flat surface. Or you
can remove the stand and mount the unit on a wall using
the recessed screw hole.
GETTING STARTED
Once batteries are in place for the remote unit, they will
start transmitting temperature readings at around 45 seconds
intervals. The main unit will also start searching for signals
for about two minutes once batteries are installed. Upon
successful reception, the outdoors temperatures will be
displayed .The main unit will automatically update its
readings at about 45-second intervals.
If no signals are received, blanks "
Hold [ ] for 2 seconds to enforce another search for about
2 minutes. This is useful in synchronizing the transmission
and reception of the remote and main units.
Repeat this step whenever you find discrepancies between the
reading shown on the main unit and that on the remote unit.
HOW TO CHECK REMOTE AND
INDOOR TEMPERATURES
The wave display on the outdoors temperature indicates
the reception of the remote unit is in good order.
If no readings are received from the remote unit for more
than two minutes, blanks " " will be displayed until
further readings are successfully searched. Check the remote
unit is sound and secure. You can wait for a little while or
Hold [ ] for 2 seconds to enforce an immediate search.
If the temperature goes above or below than the temperature
measuring range of the main unit or the remote unit (stated
in specification), the display will show "
56
BEFORE YOU BEGIN
For best operation,
1. Insert batteries for remote units before doing so for the
E
main unit.
2. Position the remote unit and main unit within effective
transmission range, which, in usual circumstances, is
F
20 to 30 meters.
RESET
D
Note that the effective range is vastly affected by the
1 2 3
CHANNEL
building materials and where the main and remote units
B
are positioned.
Try various set-ups for best result.
Though the remote units are weather proof, they should
be placed away from direct sunlight, rain or snow.
BATTERY INSTALLATION: REMOTE UNIT
1. Remove the screws on the battery compartment.
2. Select the channel
3. Install 2 batteries (UM-3 or "AA" size 1.5V) strictly
according to the polarities shown.
4. Replace the battery compartment door and secure
its screws.
BATTERY INSTALLATION: MAIN UNIT
1. Open the battery compartment door.
2. Install 2 batteries (UM-3 or "AA" size 1.5V) strictly
according to the polarities shown.
3. Replace the battery compartment door.
LOW BATTERY WARNING
When it is time to replace batteries, the respective
low-battery indicator [
outdoor temperature.
HOW TO READ THE KINETIC WAVE DISPLAY
The kinetic wave display shows the signal receiving
status of the main unit. There are three possible forms:
MAXIMUM AND MINIMUM TEMPERATURES
The maximum and minimum recorded indoor temperature,
" will be displayed. outdoor temperatures will be automatically stored in memory.
To display them, Press [ MEM ] once to display the
maximum readings and again the minimum readings.
The respective indicators,
[ MAX ] or [ MIN ] will be displayed.
To clear the memory, hold down [ MEM ] for two seconds.
The maximum and minimum readings will be erased.
If you press [ MEM ] now, the maximum and minimum
readings will have the same values as the current ones until
different readings are recorded.
"
] will show up on the indoor or
55
The unit is in searching mode.
Temperature readings are
securely registered.
No signals.
57
˚C