Black & Decker BDCDS18 Bersetzung Der Originalanweisungen Seite 8

English
(original instructions)
that is listed below but is not supplied with your sander please
visit our website at www.blackanddecker.eu.
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Item Description
Detail finger.
For small hard-to-reach areas. The detail finger can be
used for light sanding and for sanding into corners.
(Part Number - X32214-XJ)
240 grit sanding mesh.
For a fine finish for large detail sanding.
(Part Number - X39132-XJ)
120 grit sanding mesh.
For a medium finish for large detail sanding.
(Part Number - X39127-XJ)
80 grit sanding mesh.
For a coarse finish for large detail sanding.
(Part Number - X39122-XJ)
240 grit large detail sanding sheet with two
replacement tips.
For a fine finish for large detail sanding.
(Part Number - X31019-XJ)
120 grit large detail sanding sheet with two
replacement tips.
For a medium finish for large detail sanding.
(Part Number - X31009-XJ)
60 grit large detail sanding sheet with two
replacement tips.
For a coarse finish for large detail sanding.
(Part Number - X31039-XJ)
120 grit detailed finger sanding sheet.
For a medium finish for detailed sanding.
(Part Number - X3277-XJ)
Charging procedure (Fig. A)
BLACK+DECKER chargers are designed to charge
BLACK+DECKER battery packs.
Plug the charger (6) into an appropriate outlet before
inserting the battery pack (5).
Insert the battery pack (5) into the charger (6) as shown in
figure A.
The LED (6a) will flash indicating that the battery is
being charged.
The completion of charge is indicated by the LED (6a)
remaining on continuously. The pack is fully charged and
may be used at this time or left on the charger.
Note: Recharge discharged batteries as soon as possible
after use or battery life may be greatly diminished. For longest
battery life, do not discharge batteries fully.
It is recommended that the batteries be recharged after
each use.
8
Leaving the battery in the charger
The charger (6) and battery pack (5) can be left connected
with the LED glowing indefinitely.
The charger will keep the battery pack fresh and fully charged.
Important charging notes
Longest life and best performance can be obtained if the
battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge the
battery pack in an air temperature below +40°F (+4.5°C),
or above +105°F (+40.5°C). This is important and will
prevent serious damage to the battery pack.
The charger and battery pack may become warm to touch
while charging. This is a normal condition, and does not
indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack
in a warm environment such as in a metal shed, or an
uninsulated trailer.
If the battery pack does not charge properly:
Check current at receptacle by plugging in a lamp or
u
other appliance.
Check to see if receptacle is connected to a light switch
u
which turns power off when you turn out the lights.
Move charger and battery pack to a location where the
u
surrounding air temperature is approximately 65°F
- 75°F (18°- 24°C).
If charging problems persist, take the tool, battery pack
u
and charger to your local service center.
The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
Foreign materials of a conductive nature such as, but not
limited to, steel wool, aluminium foil, or any buildup of
metallic particles should be kept away from charger
cavities. Always unplug the charger from the power
supply when there is no battery pack in the cavity. Unplug
charger before attempting to clean.
Do not freeze or immerse charger in water or any
@
other liquid.
WARNING! Do not allow any liquid to get inside
charger. Never attempt to open the battery pack
for any reason. If the plastic housing of the battery
pack breaks or cracks, return to a service center
for recycling.
Charger Diagnostics (Fig.B)
Refer to the indicators in figure B for the charge status of the
battery pack.
Bad Battery
If you see a bad battery blink pattern, do not continue to
charge this battery. Return it to a service center or a collection
site for recycling.