Maintenance - Felisatti MTF 216/1100T Bedienungsanleitung

- Tighten the lock nut to make sure that the position does not
change.
OPERATION AND USE
1. CUTTING WITH THE BLADE AT 90º AND TURNTA-BLE
TURNED
- Unlock the turntable K (Fig.1) by turning lever Y to the left.
- Turn the turntable with the handle, selecting the cutting
angle required using the graduated scale R2 and index R
(Fig.1), and lock again by turning lever Y (Fig.1) to the right.
Note: there are pre-set cutting angles (0º, ±15º, ±22º30', ±30º,
±45º) on which the turntable may easily be locked.
2. CUTTING WITH THE BLADE INCLINED AND TURNTABLE
AT 0º (Fig.6) (Optional accessory)
- Move guide X outwards, in the direction of the arrow, or
even out of the machine for better operation. -
the motor unit by loosening lever O (Fig.1).
- Turn the motor unit, selecting the required inclination using
the graduated scale R1 (Fig.1) and lock lever O once more.
3. USE OF THE MITRE SAW
WARNING – Make sure that the lock button E (Fig.1) is in the
release position.
- Set the upper bench to the maximum height.
- Always start with the motor unit in rest position (raised with
the safety hook fitted)
- Fix the material to be cut firmly to the cutting plane.
- Start and wait for the blade to reach maximum revolutions.
- Press the button releasing the motor unit.
- Gradually lower the motor unit and cut.
4. BLADE START AND STOP
WARNING – make sure that the moving protector is in the correct
position when the blade is at rest (raised).
The machine is provided with a switch C (Fig.1) with push button,
which is used to start and stop the blade. It is possible to block
the switch 'ON' by pressing the lock button E (Fig.1)
WARNING – engaging the lock button disables the safety
device provided by the manufacturer and enables push-
button start. It is recommended that this device be used with
the utmost caution and ONLY when using the machine as a
circular saw.
To release the switch again, it is only necessary to press the
button and release.
5. USE OF THE CLAMP (OPTIONAL ACCESSORY)
- Raise the saw to be able to place the wood board or the
aluminium pipe on the bench for cutting and in position with
respect to guide M (Fig.1).
- Fit the clamp Z4 (Fig.5) if it is not already fitted, and turn the
bolt until the clamp press firmly on the piece to be cut, making
sure that it do not move, to avoid any accident.
- Once the operation is complete, loosen the clamp to release
the piece and change the position for the next job.
6. USE OF THE UPPER BENCH
To use the upper plane, proceed as follows:
- Make sure that the lock button E (Fig.1) is released
(standing out).
- Lower the blade unit completely and lock with pin P (Fig.1a).
- Release handles H (Fig.2) and select the height of the
upper plane, proceeding to lock the handles once more.
7. USE OF THE STOP GUIDE FOR THE UPPER BENCH (Fig.7)
Use as follows:
- Insert guide T in the upper bench.
- Select the cutting width.
- Lock guide T by tightening butterfly U followed by butterfly
S.
8. MISCELLANEOUS ACCESSORIES
The machine is supplied with the uptake nozzle included B
(Fig.1) and may therefore be connected easily to any vacuum
cleaner.
9. MISUSE
The functions and use of the tool that you have bought are only
as indicated in this manual.
Any other use of the tool is entirely prohibited.
• Do not cut aluminium or steel on the upper plane.
R e l e a s e
• Always use sharp blades suitable for the cut to be made.
• Do not use the machine without the described protection.
• Not suitable for foodstuffs.
• Use the machine only for cutting wood, aluminium profiles,
PVC tubes, steel pipes and only with the right blade.
The cutting of any other material is entirely prohib-ited.

MAINTENANCE

WARNING - before any maintenance operation, unplug the
machine.
1. LUBRICATION
The mitre saw is delivered with in all moving parts of the motor
and gearbox entirely lubricated and needs no further lubrication
operations.
Regular lubrication is recommended of the joints of the moving
controls.
2. ORDINARY CLEANING
WARNING - avoid touching the handle with hands dirty with
oil or grease. In such an event, clean immediately.
- Carefully clean the machine after use with dry com-pressed
air.
3. DISPOSAL
When the life of the machine is at an end or when it can no
longer be repaired, make sure that the scrap is disposed of in
observance of current regulations in the country of use and that
the operation is undertaken by specialised personnel authorised
in the matter.
PART REPLACEMENT
WARNING – before carrying out any replacement, unplug
the machine.
1. REPLACING THE SAW BLADE I (Fig.1)
Replace as follows:
- Set the head to fully open (Fig.1)
- Raise the upper bench as far as is allowed.
- Release the moving protection Q (Fig.2) working on button
Q1 (Fig.1a) and raise completely.
- Fit the spanner provided in the holes of the clamp, keeping
the shaft locked with another tubular spanner supplied by the
manufacturer, and unscrew the left bolt until the saw blade is