Actuating The Gas Tool; Operating The Gas Tool; Jam Clearing For Framing Nailers And Staplers; Jam Clearing For Finish Nailers - Kyocera TJEP PQZ-75 Sicherheits- Und Bedienungsanleitung

• Turn the knob to adjust the depth of drive (Fig. E).
• Repeat above procedure until you find your desired
depth of drive setting (Fig. F).
Specific for concrete nailer; push the slider side-
wards to adjust the depth.

Actuating the gas tool

• The gas tool is equipped with a full sequential actu-
ation system only.
• To actuate the gas tool, depress the safety against
the workpiece, and then pull the trigger.
• To actuate the gas tool again, you will need to re-
lease the safety fully and release the trigger before
you repeat above procedure.
• Make sure you are driving against workpiece before
you pull the trigger.

Operating the gas tool

• To ensure proper operation and avoiding overheat-
ing or choking of the gas tool, driving pace should
not exceed 1,000 shots/h and 4,000 shots/day at
optimal working conditions. High temperatures and/
or high altitudes will decrease the feasible mami-
mum number of shots per day.

Jam clearing for framing nailers and staplers

• In the case of fastener jam, disconnect the fuel cell
(Fig. B) and battery (Fig. A) before you perform any
actions.
• Release pusher to avoid pressure on the fastener
strip.
• Use a suitable tool eg. a #2 Phillips screw driver to
insert into the drive channel.
• Tap the screw driver with a hammer to push back
the driver blade and release the jam (Fig. G).
• R emove the jammed fastener with needle-nose
pliers or similar type of tool. Do not use your hand to
remove the fastener.
• If you failed to remove the jammed fastener by
above method contact your local TJEP dealer.

Jam clearing for finish nailers

• In the case of fastener jam, disconnect the fuel cell
(Fig. B) and battery (Fig. A) before you perform any
actions.
• Release pusher to avoid pressure on the fastener
strip.
• Open the driver guide cover by releasing the latch
(Fig. H).
• For TJEP ST-15/50 GAS; remove the 2 screws in
the nose piece.
• Remove the jammed fastener with needle-nose
pliers or similar type of tool. Do not use your hand to
remove the fastener.
• Secure the driver guide cover after you clear the
jam.
• For TJEP ST-15/50 GAS; reassemble the nose
piece.
10

Jam clearing for concrete nailers

• In the case of fastener jam, disconnect the fuel cell
(Fig. B) and battery (Fig. A) before you perform any
actions.
• Release pusher to avoid pressure on the fastener
strip.
• Remove magazine by releasing the magazine lock.
• Remove nozzle, clear jam and reassemble the tool.

Charging the battery and LED explanation

• There are 2 batteries supplied with the gas tool.
It will take 2 hours before the new battery is fully
charged.
• There will be green LED lightening when the battery
charger is connected to electric power and no
battery is on the battery charger.
• The LED indicator on the battery charger will turn
red when it is charging a battery.
• The other LED indicator will turn green when the
battery is fully charged.
• In the case of abnormal battery temperature, the
red LED will flash in sync with the green LED
• In the case of a defective battery, the red LED will
flash out of sync with the green LED
• When the gas tool is connected to a charged bat-
tery, the LED indicator on the tool will turn green.
State of Battery Charger LED Indicator
State Red LED
Idle – Input Power
1 OFF
Available
Battery Installed
2 ON
and Charging
Battery at Full
3 OFF
Charge
Over Temperature Blinking (ON
4
Protection 0.5s/OFF 0.5s)
Blinking (Off
5 Defect battery
0.5s/ON 0.5s)
Status
Battery capacity more than 80%
Battery capacity 80% to 60%
Battery capacity 60% to 40%
Battery capacity 40% to 20%
Battery capacity below 20%

Sleep mode and battery capacity LED

• When the battery is put into the tool, the LED will
display the battery capacity for a few seconds.
• O nce the first shot is fired, only one LED will light,
which indicates that the fan is running.
• To display the remaining battery capacity, eject the
battery and reinsert it into the tool.
• If the tool is left without use for more than two
hours, the tool will enter sleep mode to save power.
Green LED
ON
OFF
ON
Blinking (ON
0.5s/OFF 0.5s)
Blinking (ON
0.5s/OFF 0.5s)
Meaning
All LED light green
Two LED light green
One LED light green
One LED blinks green
One LED red