nedis WIFIACMB1WT14 Kurzanleitung Seite 6

-
Do not block ventilation openings and make sure that there is
enough space around the product.
1. Plug the power cable A
y into the power outlet.
Assembling the exhaust (image C)
- Only use the provided exhaust hose.
-
Do not block the exhaust hose, this may cause overheating.
1. Assemble the exhaust hose A
exhaust hose connector A u
2. Connect A to the air outlet A
u
3. Extend A
5 up to 1500 mm.
-
Do not twist the exhaust hose.
- Ensure that the exhaust hose does not kink.
4. Assemble the window kit A
5. Install A
6 in the window opening.
The window kit can be placed in horizontal and vertical
4
direction.
6. Tighten A
7 .
7. Snap A into A
4 6 and fasten with the exhaust nozzle screw
A o .
Assembling the continuous drainage (optional)
-
Works only in dehumidifying and heating mode.
1. Open the continuous drainage outlet A
2. Connect A
w to a water container or drainage system (not
included).
Placing the batteries in the remote control
1. Slide the battery cover off the back of the remote control A
2. Insert 2 type AAA batteries.
3. Slide the battery cover back in place on A
Installing the Nedis SmartLife app
1. Download the Nedis Smartlife app for Android or iOS on your
phone via Google Play or the Apple App Store.
2. Open the Nedis Smartlife app on your phone.
3. Create an account with your mobile phone number or your e-mail
address and tap Continue.
4. You will receive a verification code on your mobile phone or
e-mail address.
5. Enter the received verification code.
6. Create a password and tap Done.
7. Tap Add Home to create a SmartLife Home.
8. Set your location, choose the rooms you want to connect with
and tap Done.
Adding a product to the Nedis SmartLife app
1. Switch on the product.
2. Tap + in the Nedis SmartLife app.
3. Select the device type you want to add from the list.
4. Confirm the Wi-Fi indicator LED B
Fan speed button B
8 for 5 seconds to reset the product.
5. Follow the instructions in the Nedis SmartLife app.
Make sure you connect to the product after the product has
4
been found and added.
6. Rename the product after it has been found and added.
7. After confirming you can control the product with your
smartphone.
To connect your SmartLife account to Amazon Alexa and/ or Google
Home, set it up using the "Smart Life" action or skill. For more details
check the instruction on either Amazon or Google.
, the exhaust nozzle A
5 4
.
e .
the fasteners A
6 7 .
.
w
i
w is blinking fast, or hold the
Using the control panel and remote control
(image B)
Button
Timer button B
Mirage Button B
and the
Mode selection button
B
3
Sleep mode button B
Temperature up button
B
5
Temperature down
button B
7
Fan speed button B
Swing button B
Power button B
Temperature button B
i
Frost protection function
• The product automatically enters the frost protection status if the
temperature of the exhaust pipe is too low. (only works in cooling
mode).
• The product automatically reverts to the normal operation if the
temperature of the exhaust pipe rises to a certain temperature.
Protection function of the compressor
• To increase the lifetime of the compressor, it has a 3 minute delay
booting protection function after the compressor is switched off.
Overflow protection function
• If water exceeds the warning level, the product emits a tone, and
the 'water full' indicator starts flashing.
(See next paragraphs how to empty the water reservoir of the
product.)
Manual drainage
1. The 'water full' indicator flashes and the product emits an alarm
sound to indicate that the water reservoir is full.
2. Switch off the product using B
3. Unplug A y
4. Place a water container underneath A
5. Remove the water plug of A
6. Slightly tilt the product backwards to ensure all water leaves the
reservoir.
7. Put the water plug back on A
Declaration of Conformity
We, NEDIS, as manufacturer, declare that product WIFIACMB1WT14
from the brand Nedis, produced in China was tested according to all
relevant CE standards / regulations and passed all tests.
The complete Declaration of Conformity ( + safety datasheet if
applicable ) can be found and downloaded via http://webshop.
nedis.com
6
Function
Press to set the timer. Use B
1
B to set the duration of cooling.
7
Press to switch on the hidden display
2
on the front. Press again to turn off
the display.
Repeatedly press the button to
select the mode: Cooling mode /
Dehumidifying mode / Fan mode.
Activate sleep mode. Only works in
4
cooling mode. After one hour the set
temperature increases 1 °C and again
after 2 hours.
Increase values.
Decrease values.
Press repeatedly to select the fan
8
speed.
(Not available in sleep and
dehumidifying mode).
Switch the oscillation on or off.
9
Change the orientation of the louvers.
Switch the product on or off.
q
Switch between Celsius and
e
Fahrenheit.
q
.
.
t
t
t
5 and