Warranty And Liability; Declaration Of Conformity; Environmental Protection, Disposal - Fein KBE35 Serie Originalbetriebsanleitung

OBJ_BUCH-0000000280-002.book Page 25 Monday, April 23, 2018 3:47 PM
Operating Instructions.
Only use water-soluble cutting fluids (oil in water) as the
cooling agent.
Observe the manufacturer's instructions on coolant.
Pay attention that the set-up surface for the magnetic foot
is flat, clean, rust-free and ice-free. Remove varnish,
putty/filler layers and other materials. Prevent an air gap
between the magnetic foot and the set-up surface. The air
gap reduces the magnetic holding power.
Pay attention that the magnetic holding power is suffi-
cient.
When working non-magnetic materials, suitable FEIN
fastening devices, such as vacuum plates or pipe drilling
devices, which are available as accessories, must be used.
Observe the corresponding operating instructions for
these.
When working on steel materials with a material thick-
ness of less than 12 mm, the workpiece must be rein-
forced with an additional steel plate in order to guarantee
the magnetic holding power.
If the magnet is not positioned on a magnetisable plate or
when the magnetic foot is defective, the motor will not
start.
Work only with the absolutely required amount of feed.
Excessive feed can lead to breakage of the application
tool and loss of the magnetic holding power.
When the power supply is disconnected while the motor
is running, a protective circuit prevents automatic restart-
ing of the motor. Restart the motor again.
Do not stop the drill motor during the drilling procedure.
Only remove the core bit from the drilled hole while the
motor is running.
If the core bit should remain stuck in the material, stop
the drill motor and carefully turn the core bit out coun-
ter-clockwise.
Remove the chips and the drilled core after each drilling
process.
Do not touch the chips with your bare hands.
Always use a chip hook (6 42 01 001 00 0).
Danger of burning! The surface of the magnet can
reach high temperatures. Do not touch the magnet
with your bare hands.
When changing a drill bit, pay attention not to damage
the cutting edges.
When core drilling layered material, remove the core and
the chippings after drilling each layer.
Do not use the magnetic core drill unit when the cooling-
lubricant system is defective. Each time before operating,
check for tightness against leaks and for cracks in the
hoses. Prevent liquids from entering or penetrating elec-
trical components.
The core drills units do not have overload protection. In
case of improper use, the motor can become damaged.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
The total insulation of the power tool can be impaired.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air,
and connect a residual current device (RCD) on the line
side.
Renew stickers and warning indications on the power
tool when aged and worn.
After several hours of operation, the play in the dove-tail
guide can increase. As a consequence, the drill motor can
glide alongside the dove-tail guide by itself. This will lead
to a malfunction; when the motor glides or runs down,
the cutter can become damaged. In this case, retighten all
fastening screws of the dove-tail guide adequately so that
the drilling motor can easily be moved manually, yet does
not glide by itself (see page 14).
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available through
the FEIN customer service centre.
TThe current spares parts list for this power tool can be
found on our website at www.fein.com.
Use only original spare parts.
If required, you can change the following parts yourself:
Application tools, cooling-lubricant tank

Warranty and liability.

The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-D1_IA,
D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
en
25