Component Positioning; Appliance Safety; Preparing To Work; Inserting The Filter - Collection Bag - COMAC CA 15 EXTRA Bedienungs- Und Wartungsanleitung

The control panel components are as follows (Fig.4-5-6-7-8):
1. Vacuum nozzle.
2. Button for releasing the vacuum nozzle catch.
3. Collection tank lid release knob.
4. Slit for securing the extension hose.
5. Lifting handle.
6. Housing for winding the power cable.
7. Pin for fixing the lid of the collection tank.
8. Slot for fixing the lid of the collection tank.
9. Vacuum controller indicator light.
10. Main switch.
11. Accessories support.
The stages for making the appliance safe, thereby making it possible
to carry out operations safely, are as follows:
1. Make sure that the main switch (1) is in the rest position, if not,
disable it by pushing it (Fig.9).
2. Check that the plug (2) on the power cable (3) has been taken
out of the socket (4) of the mains supply, and if not, disconnect
it (Fig.10).
3. Wind the power cable under the appliance's lifting handle.
Before beginning to work, it is necessary to:
1. Before using, the appliance must be in order and safe to use
with the work equipment, especially the power cable and the
extension cable. If everything is not in order, the appliance must
not be used.
2. Take all necessary steps to ensure that the device is in a safe
condition (see SECURING THE
3. Insert the vacuum hose (1) from the vacuum nozzle (2) on the
collection tank, before inserting the vacuum hose press the
button (3) for unlocking the catch (Fig.11).
4. If not present in the appliance, insert a new filter - new collection
To insert the filter – collection bag inside the collection tank, proceed
as follows:
1. Take all necessary steps to ensure that the device is in a safe
condition (see SECURING THE
2. Release the vacuum tank lid (1) using the handle (2) on the back
of the collection tank, turn the handle clockwise (Fig.12).
3. Using the handle (3), in the vacuum tank lid (Fig.13), remove the
vacuum tank lid from the collection tank (rotating it and shifting
it as indicated in the figure). Put the vacuum tank lid gently on
the floor.
4. Insert the filter - paper collection bag inside the collection tank,
To insert the power cable of the appliance, proceed as follows:
1. Take all necessary steps to ensure that the device is in a safe
condition (see "MACHINE SAFETY
2. Free the vacuum tank lid (1) using the handle (2) on the front of
the collection tank, turn the handle clockwise (Fig.12).
3. Using the handle (3), in the vacuum tank lid (Fig.13), remove the
vacuum tank lid from the collection tank (rotating it and shifting
it as indicated in the figure). Put the vacuum tank lid gently on
the floor.
4. Turn the power cable catch (4) 180 degrees anti-clockwise

COMPONENT POSITIONING

APPLIANCE SAFETY

PREPARING TO WORK

PREPARING TO WORK
MACHINE'").
INSERTING THE FILTER – COLLECTION BAG
MACHINE'").

CONNECTING THE POWER CABLE

").
12. Socket for electric brush.
13. Filter - collection bag.
14. Collection tank.
15. Collection tank lid.
16. Intake air cartridge filter.
17. Intake air sponge filter:
18. Power cable.
19. Exhaust air filter.
20. Exhaust air filter compartment lid.
21. Power cable fastener.
22. Exhaust air filter compartment lid catch.
ATTENTION: Users are advised to always wear protective
gloves, to avoid the risk of serious injury to hands.
ATTENTION: To prevent damaging the power cable,
disconnect the plug from the mains socket by directly pulling
the plug and not the cable.
bag (read the section "INSERTING A FILTER - COLLECTION
BAG").
5. Select the most suitable accessory for the work to be carried out.
6. Insert the selected accessory into the vacuum hose.
7. If not present in the appliance connect the power cable (read the
section "CONNECTING THE POWER
ATTENTION: never use the appliance without the filters
supplied with the machine (COLLECTION BAG-FILTER;
INLET AIR FILTERS; EXHAUST AIR FILTER).
taking care to insert the filter correctly into the vacuum nozzle
(4) inside the collection tank and making sure not to damage the
cardboard support (5) in the bag itself (Fig.14).
5. Using the handle (3), on the vacuum tank lid, position the vacuum
tank lid on the collection tank. Being very careful to insert the
fixing pin (6) in the collection tank inside the fixing slit (7) in the
vacuum tank lid (Fig.15).
(Fig.16).
5. Insert the power cable plug (5) into the socket (6) on the
appliance (Fig.17).
6. Turn the power cable catch (4) 180 degrees clockwise, but before
doing this wind the cable inside its tear-proof housing (7) (Fig.18).
25
CABLE").