Makita LS0714 Bedienungsanleitung Seite 16

Miter angle
Left and Right 45
Right 50
Right 55
Right 57
006393
When performing compound cutting, refer to "Press
cutting", "Slide cutting", "Miter cutting" and "Bevel
cut" explanations.
6. Cutting crown and cove moldings
Crown and cove moldings can be cut on a
compound miter saw with the moldings laid flat on
the turn base.
Fig.40
There are two common types of crown moldings
and one type of cove moldings; 52/38° wall angle
crown molding, 45° wall angle crown molding and
45° wall angle cove molding. See illustrations.
(1) (2) (3) (4)
1 2
Fig.A
001556
Fig.41
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((1) and (2) in Fig.
A) and "Outside" 90° corners ((3) and (4) in Fig. A).
Measuring
Measure the wall length and adjust workpiece on
table to cut wall contact edge to desired length.
Always make sure that cut workpiece length at the
back of the workpiece is the same as wall length.
Adjust cut length for angle of cut. Always use several
pieces for test cuts to check the saw angles.
When cutting crown and cove moldings, set the
bevel angle and miter angle as indicated in the
table (A) and position the moldings on the top
surface of the saw base as indicated in the table
(B).
In the case of left bevel cut
Table (A)
Bevel angle
Molding
position in
52/38° type
Fig. A
(1)
For inside
corner
(2)
Left 33.9°
(3)
For outside
corner
(4)
006361
All manuals and user guides at all-guides.com
Bevel angle
Left 0 - 45
Left 0 - 40
Left 0 - 30
Left 0 - 25
1. Inside corner
2. Outside corner
Miter angle
45° type 52/38° type 45° type
Right 31.6° Right 35.3°
Left 30° Left 31.6° Left 35.3°
Right 31.6° Right 35.3°
Molding
Molding edge against
position in
guide fence
Fig. A
Ceiling contact edge should
(1)
be against guide fence.
For inside
corner
(2)
Wall contact edge should be
against guide fence.
For
(3)
outside
corner
Ceiling contact edge should
(4)
be against guide fence.
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° LEFT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
Lay crown molding with its broad back
•
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
The finished piece to be used will
•
always be on the LEFT side of the blade
after the cut has been made.
In the case of right bevel cut
Molding
position in
52/38° type
Fig. A
(1)
For inside
corner
(2)
Right 33.9° Right 30°
(3)
For outside
corner
(4)
006363
Molding
Molding edge against
position in
guide fence
Fig. A
Wall contact edge should be
(1)
against guide fence.
For inside
corner
(2)
Ceiling contact edge should
be against guide fence.
For
(3)
outside
corner
Wall contact edge should be
(4)
against guide fence.
006364
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° RIGHT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
Lay crown molding with its broad back
•
(hidden) surface down on the turn base
with its WALL CONTACT EDGE against
16
Table (B)
Finished piece
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.
Table (A)
Bevel angle Miter angle
45° type 52/38° type 45° type
Right 31.6° Right 35.3°
Left 31.6° Left 35.3°
Right 31.6° Right 35.3°
Table (B)
Finished piece
Finished piece
will be on the
Right side of
blade.
Finished piece
will be on the
Left side of
blade.