Intended Use; Led Display; Before Using The Appliance For The First Time - Ritter ET 10 Gebrauchs- Und Montageanleitung

English
Unfold the illustrations at the
front and back of this manual.
Please read these instructions
thoroughly before you start to
use the appliance. Keep these
operating instructions in a safe
place and ensure that they are
included with the appliance if
passing it on to a third party.
Alternatively, the current oper-
ating instructions are available
at www.ritterwerk.de.

INTENDED USE

This toaster is intended to be
used exclusively for the toast-
ing of sliced bread and bread
rolls that are suitable for
toasting in a domestic setting
and on a domestic scale.
The toaster is suitable
for contact with
foodstuffs.
If the appliance is used for
any purpose other than its
intended use, or if it is operated
incorrectly, severe injuries may
occur or the appliance may
be damaged. All warranty and
liability claims will be rendered
null and void in this case.
FUNCTIONS
The ET 10 / BT 10 built-in
toaster can be installed in any
standard drawer with a body
width of at least 30 cm. Once
installed, it is easily unfolded
and ready for use in a matter of
seconds.
The toaster includes an auto-
centring function.
Toasting
The toasting function allows
you to toast bread to your
desired toasting degree.
14
Reheating
The reheating function allows
you to reheat cold bread that
has already been toasted.
The reheating process takes
approximately 30 seconds.
Defrosting
The defrost function allows you
to thaw frozen slices of bread
and toast them to the desired
degree in a single process.
Warming-up
The integrated bread and roll
rack allows you to warm up
bread rolls for an oven-fresh
taste.
Additional functions
– The auto-centring function
automatically positions the
bread in the centre of the
toasting slot.
– The toaster switches off au-
tomatically when folded into
a horizontal position.

LED DISPLAY

The LED display provides
information about the function
that is currently in use:
Toasting
When you begin toasting,
the LED indicators light up to
indicate the toasting degree
selected. You can configure
nine different toasting degrees.
As toasting progresses, the
LED indicators switch off one
by one to allow you to estimate
the remaining toasting time.
Reheating
The LED indicators light up
and switch off one by one
when the reheating process is
completed.
Defrosting
During defrosting, the LED
indicators flash to indicate the
toasting degree selected. The
indicators do not switch off
until the bread has been fully
defrosted and toasted.
Warming-up
When the warming-up process
begins, the LED indica-
tors light up to indicate the
toasting degree selected. As
warming-up progresses, the
LED indicators switch off one
by one to allow you to estimate
how much warming-up time
remains.
BEFORE USING THE
APPLIANCE FOR THE
FIRST TIME
Preparation
• Before you use the appli-
ance for the first time, have a
specialist install it in a suitable
drawer.
• Clean the appliance before
allowing it to come into
contact with any food (see
CLEANING).
• Plug the power plug (8) into
the designated socket inside
the drawer.
• Set the toaster to "Toast"
three times without inserting
any bread into the toasting slot
(see USING THE APPLIANCE).
Ensure that there is sufficient
ventilation in the room (e.g. by
opening a window).
USING THE APPLIANCE
Preparation
• Pull out the drawer contain-
ing the toaster until it stops.
Lift the toaster by its
handle (1) and raise it into an
upright position.
• Ensure that the crumb
tray (9) is in its designated slot.
The toaster is designed so that
regular bread that is suitable
for toasting will turn golden
brown when a medium toasting
degree is selected. Toasting
to golden brown brings out the
taste of the bread perfectly.