Translation Of The Original Instructions - VERTO 50G519 Originalbetriebsanleitung

GB

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

IMPACT DRILL
50G519
NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME, READ THIS
INSTRUCTION MANUAL AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
a) Wear ear protectors when impact drilling. Exposure to noise can
cause hearing loss.
b) Use auxiliary handle(s), if supplied with the tool. Loos of control
can cause personal injury.
c) Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
d) Avoid touching rotating parts. Touching of rotating power tool
parts, equipment in particular, may cause body injury.
e) Wait until power tools comes to a complete stop before putting
it away. Working tool may jam and cause loss of control over the
power tool.
f) In case of working tool jam immediately switch off the power
tool, also be prepared for high reaction torque.
g) Fix processed material to stable surface and secure with clamps
or vice to eliminate shifting. This kind of workpiece fixation is safer
than holding the workpiece in hand.
h) Description of improper use: Do not throw the power tool, do
not overload, do not immerse in water or other fluids, do not use
for mixing adhesive or cement mortars, do not hang, carry, pull or
unplug the power tool by pulling the cord.
CAUTION! This device is designed to operate indoors. The design is
assumed to be safe, protection measures and additional safety systems
are used, nevertheless there is always a small risk of injuries at work.
Explanation of used symbols
1 2
4
5
1. Read instruction manual, observe warnings and safety conditions
therein.
2. Device with class II insulation.
3. Use personal protection measures (protective goggles, earmuff
protectors, anti-dust mask).
4. Disconnect the power cord before starting maintenance or
operation.
5. Protect against rain.
6. Keep the tool away from children.
CONSTRUCTION AND USE
Impact drills are hand operated power tools with insulation class II. Tools
are driven by single-phase commutator motors with rotational speed
reduced with gear transmission. This type of power tools is widely used
for making holes in wood, wood-like materials, metals, ceramics and
plastics (rotation only), and concrete, bricks and alike (with impact).
Range of use covers repair and building works, woodworking and any
work from the scope of individual, amateur activities (tinkering).
Use the power tool according to the manufacturer's instructions
only.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
1. Drill chuck
3
6
2. Operation mode switch
3. Switch lock button
4. Direction selector switch
5. Wheel for rotational speed control
6. Switch
7. Additional handle
8. Depth gauge rod
* Slight differences may appear between the product and drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
1. Additional handle
2. Depth gauge rod
3. Key - handwheel
4. Carrying case
*Unlike 50G519, in addition to standard equipment the 50G519K model has additional
accessories such as:
1. Tape measure 3 m
2. Socket wrenches ¼" (5-13 mm)
3. Screwdriver bits 50 mm, various
4. Adapter for socket wrenches ¼"
5. Metal drills Ø 5, 6, 8 mm
6. Masonry drills Ø 5, 6, 8 mm
7. Adjustable wrench 6"
8. Combination pliers
9. Hammer
10. Handle with socket HEX ¼"
11. Dowels and screws, assortment
PREPARATION FOR OPERATION
INSTALLATION OF ADDITIONAL HANDLE
Due to personal safety issues it is recommended to always use the
additional handle (7). Possibility to rotate the additional handle
before it is clamped on the drill body allows choosing the position
most comfortable for specific working conditions.
• Loosen the wheel lock that locks collar of the additional handle (7) by
turning it counter clockwise.
• Slide the additional handle (7) collar over cylindrical section of the
drill body.
• Turn for the most comfortable position.
• Turn the wheel lock of the additional handle (7) clockwise to clamp
the handle.
DEPTH GAUGE INSTALLATION
Depth gauge rod (8) is used to limit the depth of drill penetration in
material.
• Loosen the wheel lock, which blocks collar of the additional handle (7).
• Slide depth gauge rod (8) into the hole in the additional handle collar.
• Set desired drilling depth.
• Fix by tightening the wheel lock of the additional handle (7) collar.
INSTALLATION OF WORKING TOOLS
Disconnect the power tool from power supply.
• Insert key into one of the holes on the circumference of the drill chuck (1).
• Open jaws to desired dimension.
• Insert cylindrical drill shank into the drill chuck (1), push it to the limit.
• Tighten jaws on drill shank with the key (insert it into three holes on
the drill chuck circumference).
Remember to always remove the key from the chuck after you finish
drill installation or removal.
OPERATION / SETTINGS
SWITCHING ON / SWITCHING OFF
The mains voltage must match the voltage on the label of the drill.
Switching on – press the switch button (6) and hold in this position.
Switching off – release pressure on the switch (6).
Locking the switch (continuous operation)
9
– 1 pce
– 1 pce
– 1 pce
– 1 pce
– 1 pce
– 9 pcs
– 4 pcs
– 1 pce
– 3 pcs
– 3 pcs
– 1 pce
– 1 pce
– 1 pce
– 1 pce
– 1 set