Norwood LumberMate LM29V2 Anleitung Seite 8

Before operating the equipment, ensure that:
•
all maintenance procedures have been properly carried
out;
•
the blade is disengaged;
•
the equipment stands firmly and securely and the rails
are fully supported along their full length;
•
the carriage retaining keepers and bed end stops are
properly and securely installed;
•
all components, fasteners, cables and parts are properly
and securely installed and in good working order;
•
all safety features are properly and securely installed
and in good working order including, but not limited to,
the electric motor circuit breaking safety switch, the
blade/bandwheel brake, the sawdust chute cage, and
blade and bandwheel guards are correctly installed and
securely locked; and
•
the blade is correctly installed, properly tensioned and
aligned, and can rotate freely in the correct direction.
Before each cut, ensure that:
•
no person other than the operator and no pets are within
the minimum safety distances;
•
the worksite is free of objects that the operator can trip
over, hazards or distractions.
•
the blade will clear the log posts and log dogs;
•
the rails and track are free of debris;
•
the log is firmly secured with the log clamping
mechanisms;
•
the adjustable blade guide will clear the widest portion of
the next cut by one inch and is secured in place;
•
the blade and bandwheel guards are correctly installed
and securely locked; and
•
the operator is wearing all personal protective equipment.
At regular intervals during operation, ensure that no
person other than the operator and no pets are within the
minimum safety distances.
Turn the motor off if you are going to leave the operating
station behind the carriage, even just temporarily, for
example when loading or repositioning logs or removing
lumber.
Never overreach. Keep proper footing at all times.
Discontinue operating the equipment or handling blades
if you become fatigued or distracted.
Stay focused and alert. Watch what you are doing. Use
common sense.
If your sawmill is equipped with an electric powered
motor:
Risk of electric shock! Hazardous voltage inside the
disconnect box, starter box and at the electric motor can
cause shock, burns or death.
Electrical short danger! Ensure that you do not short
out any part of the electrical system. Shorting out
the electrical system can cause both of the sawhead
support cables to simultaneously break suddenly and the
sawhead to drop violently causing serious injury.
EN–4
MILL-ELEC-S1-MANEN (2021-07-14).indd 4 MILL-ELEC-S1-MANEN (2021-07-14).indd 4
Only a qualified electrician can open the electrical
equipment. All electrical installation, service and
maintenance work must be performed by a qualified
electrician and must be performed in accordance to
applicable electrical codes. Failure to do so can result in
serious injury or death.
Before installing, servicing or maintaining any of the
electrical equipment, turn the control panel to the OFF
position and disconnect (unplug) the power supply
electrical cable from your electrical outlet. Follow all
applicable electrical codes.
If you have any reason to suspect that there is anything
wrong with the electrical system, immediately disconnect
(unplug) the power supply electrical cable from your
electrical outlet, turn the control panel to the OFF
position and remove the ignition key and contact a
qualified electrician to service the electrical equipment.
Do not operate the equipment until it has been serviced
by a qualified electrician and certified fully safe to operate
Storing the Equipment
When storing the equipment, turn the control panel to the
OFF position and disconnect (unplug) the power supply
electrical cable from your electrical outlet. Take any other
measures necessary to prevent unauthorized operators
from accessing or starting the equipment.
Ensure that the blade and bandwheel guards are
correctly installed and securely locked.
Lower the sawhead to its lowest position.
Always store the equipment in a secure and locked
location completely inaccessible by children or any
persons.
When not in use or when unattended, even for short
periods of time such as during breaks, remove the blade
from the sawmill and store it in a location inaccessible by
children or any persons. In addition to being a wise safety
precaution, removing the blade from the sawmill ensures
that it is not stored under tension and so prevents
premature blade fatigue.
When not in use, take measures to secure thecarriage to
the bed to prevent the carriage from being blown or
inadvertently rolled along the track.
Always store all blades in a secure and locked location
completely inaccessible by children or any persons.
If your sawmill is equipped with the optional trailer
package: When storing the equipment, always remove
the drawbar and wheels and secure them in a different
location and take any other measures necessary to
prevent unauthorized persons from accessing or moving
the equipment.
The machine can be stored under ambient
tempera¬tures between -25 °C and +55 °C.
When storing the equipment, turn the electric motor OFF
and remove the blade. Disconnect (unplug) the power
supply electrical cable from your electrical outlet.
2021-07-14 3:54:01 PM 2021-07-14 3:54:01 PM