Makita LS1216 Betriebsanleitung Seite 24

1. Miter angle
Push the carriage toward the guide fence and tighten the
locking screw clockwise and pull the lock lever toward
yourself to secure the carriage.
Turn the grip counterclockwise which secures the turn
base. Turn the turn base so that the pointer points to 0°
on the miter scale. Then turn the turn base slightly clock-
wise and counterclockwise to seat the turn base in the 0°
miter notch. (Leave as it is if the pointer does not point to
0°.) Loosen the hex socket bolts securing the guide fence
using the socket wrench.
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex
socket bolts on the guide fence in the order from the right
side. (Fig. 56)
Make sure that the pointer points to 0° on the miter scale.
If the pointer does not point to 0°, loosen the screw which
secures the pointer and adjust the pointer so that it will
point to 0°. (Fig. 57)
2. Bevel angle
Push the latch lever forward fully to release the positive
stops.
1) 0° bevel angle
Push the carriage toward the guide fence and
tighten the locking screw clockwise and pull the lock
lever toward yourself to secure the carriage. Lower
the handle fully and lock it in the lowered position by
pushing in the stopper pin. Loosen the lever at the
rear of the tool. (Fig. 58)
Turn the hex socket bolt on the right side of the arm
holder two or three revolutions counterclockwise to
tilt the blade to the right. (Fig. 59)
Carefully square the side of the blade with the top
surface of the turn base using the triangular rule, try-
square, etc. by turning the hex socket bolt on the
right side of the arm holder clockwise. Then tighten
the lever securely. (Fig. 60)
Make sure that the pointers on the arm holder point
to 0° on the bevel scale plate on the arm. If they do
not point to 0°, loosen the screws which secure the
pointers and adjust them so that they will point to 0°.
(Fig. 61)
2) 45° bevel angle (Fig. 62)
Adjust the 45° bevel angle only after performing 0°
bevel angle adjustment. To adjust left 45° bevel
angle, loosen the lever and tilt the blade to the left
fully. Make sure that the pointer on the arm holder
points to 45° on the bevel scale on the arm. If the
pointer does not point to 45°, turn the left 45° bevel
angle adjusting bolt on the side of the arm until the
pointer points to 45°.
To adjust right 45° bevel angle, perform the same
procedure described above.
Adjusting the position of laser line (Fig. 63 & 64)
For model LS1216L only
WARNING:
• As the tool is plugged when adjusting the position of
laser line, take a full caution especially at switch action.
Pulling the switch trigger accidentally cause an acci-
dental start of the tool and personal injury.
CAUTION:
• Never look into the laser beam directly. Direct laser
beam causes damage to your eyes.
24
• LASER RADIATION
Do not stare into beam.
• Never apply a blow or impact to the tool. A blow or
impact causes the incorrect position of laser line, dam-
age to the laser beam emitting part or a short life of the
tool.
When adjusting the laser line appears on the left side
of the saw blade
1
1 Screw to change the movable range of the adjusting
screw
2 Adjusting screw
3 Hex wrench
4 Laser line
5 Saw blade
When adjusting the laser line appears on the
right side of the saw blade
1
1 Adjusting screw
2 Saw blade
3 Laser line
For both adjustments, do as follows.
1. Make sure that the tool is unplugged.
2. Draw the cutting line on the workpiece and place it
on the turn table. At this time, do not secure the
workpiece with a vise or similar securing device.
3. Lower the blade by lowering the handle and just
check to see where the cutting line and the position
of the saw blade is. (Decide which position to cut on
the line of cut.)
4. After decision the position to be cut, return the han-
dle to the original position. Secure the workpiece
with the vertical vise without shifting the workpiece
from the pre-checked position.
5. Plug the tool and turn on the laser switch.
6. Adjust the position of laser line as follows.
The position of laser line can be changed as the movable
range of the adjusting screw for the laser is changed by
turning two screws with a hex wrench. (The movable
range of laser line is factory adjusted within 1 mm from
the side surface of blade.)
To shift the laser line movable range further away from
the side surface of blade, turn the two screws counter-
clockwise after loosening the adjusting screw. Turn these
two screws clockwise to shift it closer to the side surface
of the blade after loosening the adjusting screw.
4
2
3
2
3
5