DeWalt DWD014 Originalanweisung Seite 23

Keyed Chuck (Fig. A–C)
DWD014
The DWD014 features a keyed chuck
other accessory, follow the steps listed below.
1. Open the chuck jaws by turning collar by hand and insert
the shank of the bit about 19 mm into chuck. Tighten the
chuck collar by hand.
2. Place chuck key in each of the three holes, and tighten in
clockwise direction. It's important to tighten chuck with all
three holes.
To release the bit, turn the chuck counterclockwise in just one
hole, then loosen the chuck by hand.
Removal of Keyed Chuck (Fig. B)
Tighten the chuck around the shorter end of a hex key (not
supplied) of 6 mm or greater size. Using a soft hammer, strike
the key sharply in the counterclockwise direction when viewed
from the front of the tool. This will loosen the chuck so that it
can be removed by hand.
Keyed Chuck Installation (Fig. C)
Screw the chuck on by hand as far as it will go. Insert the shorter
end of a hex key (not supplied) of 6 mm or greater size and
strike it in the clockwise direction with a soft hammer.
Keyless Chuck (Fig. D–F)
DWD014S, DWD014S-XE
The DWD014S, DWD014S-XE features a keyless chuck
greater convenience. To insert a drill bit or other accessory,
follow the steps listed below.
1. Grasp the rear half of the chuck with one hand and use
your other hand to rotate the front half counterclockwise,
as shown in Figure D. Rotate far enough so that the chuck
opens sufficiently to accept the desired accessory.
2. Insert the bit or other accessory about 19 mm into the chuck
and tighten securely by holding the rear half of the chuck
and rotating the front portion in the clockwise direction.
When the chuck is nearly tightened, you will hear a clicking
sound. After 4–6 clicks, the chuck is securely tightened
around the accessory.
3. To release the accessory, repeat step 1 listed above.

WARNING: Do not attempt to tighten drill bits (or any
other accessory) by gripping the front part of the chuck
and turning the tool on. Damage to the chuck and
personal injury may result.
Keyless Chuck Removal (Fig. E)
Tighten the chuck around the shorter end of a hex key (not
supplied) of 6 mm or greater size. Using a soft hammer or piece
of wood, strike the longer end in the counterclockwise direction.
This will loosen the chuck so that it can be unscrewed by hand.
Keyless Chuck Installation (Fig. F)
Screw the chuck on by hand as far as it will go. Tighten the
chuck around the shorter end of a 6 mm or larger hex key (not
supplied) strike the longer end in the clockwise direction with a
soft hammer.
4 . To insert a drill bit or
4 for
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.
Proper Hand Position (Fig. G)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main handle

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Trigger Switch (Fig. A)
To start the drill, depress the trigger switch; to stop the drill,
release the trigger switch.
nOTE: Use lower speeds for starting holes without a
center punch, drilling in metal or plastics, driving screws
or drilling ceramics. Higher speeds are better for drilling
wood and composition boards and using abrasive and
polishing accessories.
Variable Speed
A variable speed trigger switch
farther the trigger is depressed, the higher the speed of the drill.
For continuous operation, press and hold the variable speed
switch, move the lock-on button
To stop continuous operation, press the switch briefly and
release it. Always switch the tool off when work is finished and
before unplugging.
Speed Dial (Fig. A)
DWD014S, DWD014S-XE
To reduce the speed, turn the speed dial
increase speed, turn the dial clockwise.
Drilling

WARNING: To reduce the risk of personal injury,
ALWAYS ensure workpiece is anchored or clamped firmly.
If drilling thin material, use a wood "back-up" block to
prevent damage to the material.
1. Use sharp drill bits only. For WOOD, use twist drill bits, spade
bits, power auger bits, or hole saws. For METAL, use steel
twist drill bits or hole saws.
2. Always apply pressure in a straight line with the bit. Use
enough pressure to keep drill biting, but do not push hard
enough to stall the motor or deflect the bit.
3. Hold tool firmly with both hands to control the twisting
action of the drill.
EnGLIsH
1 permits speed control—the
2 up, then release the switch.
7 counterclockwise. To
8 .
21