Makita LS1016 Bedienungsanleitung Seite 15

2. With the adjusting screw loosened, slide the
adjusting screw to the right or left as far as it goes.
3. Tighten the adjusting screw firmly at the position
where it stops sliding.
Laser line is factory adjusted so that it is positioned
within 1 mm from the side surface of the blade (cutting
position).
NOTE:
When laser line appears dim and hard to see
•
because of direct sunlight, relocate the work area
to a place where there is less direct sunlight.
Aligning the laser line
Fig.21
Laser line can be shifted to either the left or right side of
the blade according to the applications of cutting. Refer
to explanation titled "Laser beam action" regarding its
shifting method.
NOTE:
Use wood facing against the guide fence when
•
aligning the cutting line with the laser line at the
side of guide fence in compound cutting (bevel
angle 45 degrees and miter angle right 45
degrees).
A) When you obtain the correct size on the left side of
workpiece
Shift the laser line to the left of the blade.
•
B) When you obtain the correct size on the right side of
workpiece
Shift the laser line to the right of the blade.
•
Align the cutting line on your workpiece with the laser
line.
ASSEMBLY
WARNING:
Always be sure that the tool is switched off and
•
unplugged before working on the tool. Failure to
switch off and unplug the tool may result in serious
personal injury.
Socket wrench storage
Fig.22
The socket wrench is stored as shown in the figure.
When the socket wrench is needed it can be pulled out
of the wrench holder. After using the socket wrench it
can be stored by returning it to the wrench holder.
Installing or removing saw blade
WARNING:
Always be sure that the tool is switched off and
•
unplugged before installing or removing the
blade. Accidental start up of the tool may result in
serious personal injury.
Use only the Makita socket wrench provided to
•
install or remove the blade.Failure to use the
wrench may result in overtightening or insufficient
tightening of the hex bolt and serious personal
injury.
Fig.23
Lock the handle in the raised position by pushing in the
stopper pin.
Fig.24
To remove the blade, use the socket wrench to loosen
the hex bolt holding the center cover by turning it
counterclockwise. Raise the blade guard and center
cover.
Fig.25
Press the shaft lock to lock the spindle and use the
socket wrench to loosen the hex bolt clockwise. Then
remove the hex bolt, outer flange and blade.
Fig.26
Fig.27
NOTE:
If the inner flange is removed be sure to install it on
•
the spindle with its protrusion facing away from the
blade. If the flange is installed incorrectly the
flange will rub against the machine.
WARNING:
Before mounting the blade onto the spindle,
•
always be sure that the correct ring for the
blade's arbor hole you intend to use is installed
between the inner and the outer flanges. Use of
the incorrect arbor hole ring
improper mounting of the blade causing blade
movement and severe vibration resulting in
possible loss of control during operation and in
serious personal injury.
To install the blade, mount it carefully onto the spindle,
making sure that the direction of the arrow on the
surface of the blade matches the direction of the arrow
on the blade case.
Fig.28
Install the outer flange and hex bolt, and then use the
socket wrench to tighten the hex bolt (left-handed)
securely counterclockwise while pressing the shaft lock.
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Release the handle from the raised
position by pulling the stopper pin. Lower the handle to
make sure that the blade guard moves properly. Make
sure the shaft lock has released spindle before making
cut.
Dust bag
Fig.29
The use of the dust bag makes cutting operations
cleaner and dust collection easier. To attach the dust
bag, fit it onto the dust nozzle.
When the dust bag is about half full, remove the dust
bag from the tool and pull the fastener out. Empty the
15
may result in the