Makita LS1016 Bedienungsanleitung Seite 14

WARNING:
Before plugging in the tool, always check to
•
see that the switch trigger actuates properly
and returns to the "OFF" position when
released. Do not pull the switch trigger hard
without pressing in the lock-off button. This
can cause switch breakage. Operating a tool with
a switch that does not actuate properly can lead to
loss of control and serious personal injury.
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
For all countries other than European countries
Fig.17
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
WARNING:
Before plugging in the tool, always check to
•
see that the switch trigger actuates properly
and returns to the "OFF" position when
released. Do not pull the switch trigger hard
without pressing in the lock-off button. This
can cause switch breakage. Operating a tool with
a switch that does not actuate properly can lead to
loss of control and serious personal injury.
A hole is provided in the switch trigger for insertion of
padlock to lock the tool off.
WARNING:
Do not use a lock with a shank or cable any
•
smaller than 6.35 mm in diameter. A smaller
shank or cable may not properly lock the tool in the
off position and unintentional operation may occur
resulting in serious personal injury.
NEVER use tool without a fully operative
•
switch trigger. Any tool with an inoperative switch
is HIGHLY DANGEROUS and must be repaired
before further usage or serious personal injury may
occur.
For your safety, this tool is equipped with a lock-off
•
button which prevents the tool from unintended
starting. NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the
lock-off button. A switch in need of repair may
result in unintentional operation and serious
personal injury. Return tool to a Makita service
center for proper repairs BEFORE further usage.
NEVER defeat the lock-off button by taping down
•
or some other means. A switch with a defeated
lock-off button may result in unintentional operation
and serious personal injury.
Lighting up the lamps
For Models LS1016F and LS1016FL only
Fig.18
CAUTION:
This is not a rainproof light. Do not wash the light in
•
water or use it in a rain or a wet area. Such a
conduct can cause an electric shock and fume.
Do not touch the lens of the light, as it is very hot
•
while it is lighted or shortly after it is turned off. This
may cause a burn to a human body.
Do not apply impact to the light, which may cause
•
damage or shorted service time to it.
Do not keep casting the beam of the light to your
•
eyes. This can cause your eyes to be hurt.
Do not cover the light with clothes, carton,
•
cardboard or similar objects while it is lighted,
which can cause a fire or an ignition.
To turn on the light, press the upper position (I) of the
switch. To turn off the light, press the lower position (O)
of the switch.
Move the light to shift an area of lighting.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp.
•
Be careful not to scratch the lens of light, or it may
lower the illumination.
Electronic function
Constant speed control
The tool is provided with an electronic speed
•
control which helps maintain a constant blade
rotation speed even under load. A constant blade
rotation speed will result in a very smooth cut.
Soft start feature
This function allows the smooth start-up of the tool
•
by limiting the start-up torque.
Laser beam action
For models LS1016L and LS1016FL only
Fig.19
CAUTION:
Never look into the laser beam. Direct laser beam
•
may injure your eyes.
LASER RADIATION, DO NOT STARE INTO THE
•
BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS, CLASS 2M LASER PRODUCT.
To turn on the laser beam, press the upper position (I) of
the switch. To turn off the laser beam, press the lower
position (0) of the switch.
Laser line can be shifted to either the left or right side of
the saw blade by adjusting the adjusting screw as
follows.
Fig.20
1. Loosen the adjusting screw by turning it
counterclockwise.
14