Makita DLM533 Betriebsanleitung Seite 15

Hold the front grip or the lower handle with one hand,
and then move the mowing height adjusting lever with
the other hand.
► Fig.19: 1. Mowing height adjusting lever 2. Lower
handle 3. Front grip
NOTE: The mowing height figures should be used
just as a guideline. Depending on the conditions of
the lawn or the ground, the actual lawn height may
become slightly different from the set height.
NOTE: Try a test mowing of grass in a less conspicu-
ous place to get your desired height.
Grass level indicator
Grass level indicator shows the volume of mowed
grass. When the grass basket is not full, the indicator
floats while the blades are running.
► Fig.20: 1. Grass level indicator
When the grass basket is almost full, the indicator does
not float while the blades are running. In this case, stop
the operation immediately and empty the basket.
► Fig.21: 1. Grass level indicator
NOTE: This indicator is a rough guide. Depending on
the conditions of inside of the basket, this indicator
may not work properly.
Adjusting the handle height
CAUTION:
Before removing the bolts, hold
the upper handle firmly. Otherwise, the handle may
fall and cause an injury.
The handle height can be adjusted in two levels.
1. Remove the upper bolts of the lower handle using
box wrench 13, and then loosen the lower bolts.
► Fig.22: 1. Upper bolt 2. Lower bolt
2. Adjust the handle height, and then tighten the
upper and lower bolts firmly.
Adjusting the traveling speed
► Fig.23: 1. Speed lever
The traveling speed can be adjusted with the speed
lever. To decrease the speed, pull the lever toward you,
and to increase the speed, turn the lever forward.
Using mulching plug
The mulching plug allows you to return the cut grass to
the ground without gathering the cut grass in the grass
basket. When you operate the machine with the mulch-
ing plug, be sure to remove the grass basket.
NOTICE:
When using the machine with the
mulching plug, make sure that the total length of
grass is 30 mm or more, or the cut length is 15
mm or less.
► Fig.24: (1) 30 mm or more (2) 15 mm or less
Using the rear discharge
Using the rear discharge allows you to discharge the cut
grass to the ground from the rear side of the machine
without gathering the cut grass in the grass basket.
When you operate the machine using the rear dis-
charge, be sure to remove the grass basket and mulch-
ing plug, and close the rear cover.
Electronic function
The machine is equipped with the electronic functions
for easy operation.
• Constant speed control of blade rotation
Electronic speed control for obtaining constant
speed. Possible to get fine finish, because the
rotating speed is kept constant even under load
condition.
• Soft start at driving
The soft-start function minimizes start-up shock,
and makes the machine start smoothly.
• Electric brake
This machine is equipped with an electric brake.
If the machine consistently fails to quickly stop
the mower blades after releasing the switch lever,
have the machine serviced at Makita Authorized
Service Center.
OPERATION
Mowing
WARNING:
and stones from mowing area. Furthermore, clear
away any weeds from mowing area in advance.
WARNING:
safety glasses with side shields when operating
the mower.
CAUTION:
If the cut grass or foreign object
blocks up inside of the mower body, be sure to
remove the lock key and battery cartridge and
wear gloves before removing the grass or foreign
object.
NOTICE:
Use this machine for mowing lawn only.
Do not mow weeds with this machine.
► Fig.25
Firmly hold the handle with both hands when mowing.
The mowing speed guideline is approximately 7 to 14
meters per 10 seconds.
► Fig.26
The center lines of the front wheels are guidelines to
mowing width. Using the center lines as guidelines,
mow in strips. Overlap by one half to one third the previ-
ous strip to mow the lawn evenly.
► Fig.27: 1. Mowing width 2. Overlapping area
3. Center line
15 ENGLISH
Before mowing, clear away sticks
Always wear the safety goggles or