Seite 1
Guida rapida Quick Guide Kurzanleitung 40164 Interfaccia telefonica per citofoni e videocitofoni Due Fili Plus Telephone interface for Due Fili Plus entryphones and video entryphones Telefonschnittstelle für Haustelefone und Videohaustelefone Due Fili Plus...
40164 - Interfaccia telefonica Due Fili Plus 1. Descrizione L’interfaccia telefonica 40164 consente l’inoltro delle chiamate videocitofoniche Due Fili Plus, ad un telefono remoto, o con l’ausilio di un centralino telefonico, ad un telefono interno. Consente inoltre di fare un’autoaccensione della targa principale, aprire la serratura in targa o comandare dei relè.
40164 - Interfaccia telefonica Due Fili Plus Dip-Switch - selettore di impedenza OFF – OFF : nessuna impedenza ON – OFF : impedenza 100 ohm ON – ON : impedenza 50 ohm 40164 Phone interface 2F+ Regolazione 50 mA Volume TX...
40164 - Interfaccia telefonica Due Fili Plus 3. Modalità d’utilizzo Modalità STANDARD La Modalità STANDARD è la modalità di Default dell’interfaccia. In questa modalità l’interfaccia lavora con gli ID dei Posti interni da 1 a 4. Se gli ID dell’impianto non vanno da 1 a 4 si deve vedere il paragrafo 5.9 di programmazione degli ID dedicato.
40164 - Interfaccia telefonica Due Fili Plus Modalità CENTRALINO Abbinando l’interfaccia 40164 ad un centralino telefonico 40510 è possibile gestire le chiamate citofoniche direttamente da dei telefoni. Programmazione in modalità CENTRALINO e associazione di un telefono Se l’interfaccia è collegata direttamente alla linea telefonica, da un telefono esterno chiamiamo il numero telefonico della linea a cui è...
40164 - Interfaccia telefonica Due Fili Plus 4. Guida all’uso per l’utente Rispondere ad una chiamata in arrivo dall’impianto video/citofonico All’arrivo della chiamata sollevare la cornetta o premere il pulsante di risposta Per attivare la comunicazione fonica premo il tasto * Premere il tasto # per aprire la porta...
40164 - Interfaccia telefonica Due Fili Plus 5. Technical characteristics • TELEPHONE INPUT: Input voltage: 24-48 VDC Maximum absorbed current: • Standby: 38 mA • Calling: 50 mA Ring signal recognised: 35Veff 25Hz/50Hz Busy tone recognition: Frequency 425Hz +/- 5Hz; minimum tone duration 300ms •...
40164 - Due Fili Plus telephone interface 1. Description The telephone interface 40164 allows you to forward Due Fili Plus video door entry calls to a remote telephone or to an internal telephone with the aid of a telephone switchboard.
40164 - Due Fili Plus telephone interface Dip Switch - impedance selector OFF – OFF: no impedance ON – OFF: 100 Ohm impedance ON – ON: 50 Ohm impedance 40164 Phone interface 2F+ TX Volume 50 mA adjustment RX Volume...
40164 - Due Fili Plus telephone interface 3. Operating modes STANDARD mode STANDARD mode is the Default mode of the interface. In this mode, the interface works with the IDs of Indoor Stations from 1 to 4. If the IDs of the system are not from 1 to 4 please refer to paragraph 5.9 for programming the dedicated ID.
40164 - Due Fili Plus telephone interface SWITCHBOARD mode By combining the interface 40164 with a telephone switchboard 40510 entryphone calls can be managed directly from telephones. Programming the SWITCHBOARD mode and associating a telephone If the interface is connected directly to the telephone line, from an external telephone we call the telephone number of the line to which the interface is connected and wait for the three confirmation tones.
40164 - Due Fili Plus telephone interface 4. User guide Answering an incoming call from the video/entryphone system When a call arrives, raise the handset or press the answer push button To activate voice communication press the * key Press the # key to open the door Continue the call or hang up...
• DIMENSIONS: H x L x D: 85x53x66mm (3 DIN modules) The instructions manual can be downloaded from the website www.vimar.com Installation rules Installation must be carried out by qualified persons in compliance with the current regulations regarding the installation of electrical equipment in the country where the products are installed.
40164 - Telefonschnittstelle Due Fili Plus 1. Beschreibung Mit der Telefonschnittstelle 40164 können Anrufe der Videosprechanlagen Due Fili Plus an ein entferntes Telefon bzw. mithilfe einer Telefonzentrale an ein internes Telefon weitergeleitet werden. Sie ermöglicht außerdem die Selbsteinschaltung des Haupt-Klingeltableaus, die Öffnung des Klingeltableau- Türschlosses oder die Steuerung von Relais.
(Frontansicht) (Rückansicht) 2. Installation Die Videosprechanlage installieren und ihre korrekte Funktionsweise prüfen. • 40164 auf einem Rahmen für DIN-Schiene befestigen. • Die Stromversorgung der Videosprechanlage trennen. • Die "Leitungsklemmen" an eine Innenstelle (N) der Telefonzentrale oder direkt an die Telefonleitung anschließen.
40164 - Telefonschnittstelle Due Fili Plus 3. Funktionsmodus STANDARD-Modus Der STANDARD-Modus ist der werkseitige Funktionsmodus der Schnittstelle. In diesem Modus arbeitet die Schnittstelle mit den Innenstellen-ID 1 bis 4. Liegen die ID der Anlage nicht im Bereich 1 bis 4, siehe den Abschnitt 5.9 zur Programmierung der ID.
Schnittstelle wieder anrufen und die Programmierung ab dem letzten Code fortsetzen. Modus ZENTRALE Durch Kombination der Schnittstelle 40164 mit einer Telefonzentrale 40510 können die Haustelefonrufe direkt anhand von Telefonen verwaltet werden. Programmierung im Modus ZENTRALE und Kopplung eines Telefons Ist die Schnittstelle direkt an die Telefonleitung angeschlossen, wird von einem Außentelefon die Rufnummer der...
40164 - Telefonschnittstelle Due Fili Plus 4. Benutzeranleitung Einen eingehenden Anruf der Video-/Türsprechanlage entgegennehmen Bei eingehendem Anruf den Hörer abnehmen oder die Taste Antworten drücken Um die Sprechverbindung zu aktivieren, die Taste * drücken Mit Taste # die Tür öffnen Das Gespräch fortsetzen oder den Anruf beenden...
DIGITALER BUSEINGANG: Konform mit Due Fili Bus • ABMESSUNGEN: L x H x T: 85x53x66mm (3 DIN-Module) Die Bedienungsanleitung ist auf der Website www.vimar.com zum Download verfügbar Installationsvorschriften Die Installation muss durch Fachpersonal gemäß den im Anwendungsland des Geräts geltenden Vorschriften zur Installation elektrischen Materials erfolgen.