Cleaning; Storage; Maintenance; Disposal And Recycling - Scheppach 5909212900 Original Bedienungsanleitung

Switching on and off
Switching on:
To start the appliance, press the ON/OFF switch (4)
and keep it pressed in.
The LED working light (2) lights up when the ON/OFF
switch (4) is depressed lightly or fully. This provides
illumination of the work area in poor lighting condi-
tions.
Switching off:
Release the ON/OFF switch (4) to switch off the ap-
pliance.
Setting/preselecting the rotation speed/tighten-
ing torque
Press the ON/OFF switch (4) lightly for a low speed/
tightening torque.
Increasing the pressure increases the speed/tighten-
ing torque. The tightening torque depends on the se-
lected speed/torque preselection and impact duration.
NOTE
However, to tighten lug nuts, the smallest torque set-
ting must be selected to avoid over tightening.
CAUTION!
The tightening torque actually attained must always
be checked with a torque wrench!
NOTE
The integrated motor brake ensures rapid stoppage.
Changing the direction of rotation
Change the direction of rotation by pressing the rota-
tion direction switch (3) towards the left or right.

11. Cleaning

Danger!
Always pull out the battery pack before starting any
cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
• We recommend that you clean the device immedi-
ately each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep into
the device. The ingress of water into an electric tool
increases the risk of an electric shock.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

12. Storage

Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C. Store the electrical tool in its original packag-
ing. Cover the electrical tool in order to protect it from
dust and moisture. Store the operating manual with
the electrical tool.

13. Maintenance

There are no parts inside the equipment which re-
quire additional maintenance.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: Carbon brushes
* Not necessarily included in the scope of delivery!

14. Disposal and recycling

The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and
electronic equipment (WEEE). This product must be
disposed of at a designated collection point. This can
occur, for example, by handing it in at an authorised
collecting point for the recycling of waste electrical
and electronic equipment. Improper handling of
waste equipment may have negative consequences
for the environment and human health due to poten-
tially hazardous substances that are often contained
in electrical and electronic equipment. By properly
disposing of this product, you are also contributing
to the effective use of natural resources. You can
obtain information on collection points for waste
equipment from your municipal administration, pub-
lic waste disposal authority, an authorised body for
the disposal of waste electrical and electronic equip-
ment or your waste disposal company.