Introduction; Device Description (Fig. 1-9); Scope Of Delivery - Scheppach DP60 Original Bedienungsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the
user to become familiar with the machine and take
advantage of its application possibilities in accord-
ance with the recommendations.
The operating instructions contain important informa-
tion on how to operate the machine safely, profes-
sionally and economically, how to avoid danger, cost-
ly repairs, reduce downtimes and how to increase
reliability and service life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regu-
lations that apply for the operation of the machine in
your country.
Keep the operating instructions package with the
machine at all times and store it in a plastic cover to
protect it from dirt and moisture. Read the instruction
manual each time before operating the machine and
carefully follow its information.
The machine can only be operated by persons who were
instructed concerning the operation of the machine and
who are informed about the associated dangers. The
minimum age requirement must be complied with.
In addition to the safety instructions contained in this op-
erating manual and the specific regulations of your coun-
try, the technical rules generally accepted for the oper-
ation of machines of the same type must be observed.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.

2. Device description (fig. 1-9)

1. Base plate
2. Quick clamp
3. Column
4. Toothed rack for height adjustment
5. Clamping lever for height adjustment
6. Clamping lever for depth stop
7. Depth stop
8. Handle
8.1 Mounting mandrel
8.2 Spacer sleeve
8.3 Handle cover
9. Display
10. Off switch
11. On switch
12. Speed control
13. Chuck guard
14. Chuck
15. Wing screws for parallel stop
16. Parallel stop
17. Quick clamp lever
18. Gear selector switch
19. Allen key
20. Open-ended spanner
A. Fixing screw (pre-mounted)
B. Philips screw handle
C. Screw
D. Retainer
E. Table mounting attachment kit
F. Speed / drilling depth selector switch
G. Zero point button
H. Laser cross on / off switch
I. LED work lamp on / off switch
J. Holding ring
K. Securing ring
L. Clamping sleeve

3. Scope of delivery

• 1 drilling machine
• 1 quick clamp (2)
• 1 base plate (1)
• 1 parallel stop (16)
• 1 handle (8)
• 1 chuck guard (13)
• 2 screws 3.0 x 12
• 1 clamping lever (6)
• 1 depth stop (7)
• 1 Allen key, 4 mm (19)
• 1 open-ended spanner (flat), 16 mm
• 1 screw bag: 4 screws M8 x 50, 4 nuts M8, 8 washers
• 1 operating manual
GB | 21