Operation - Makita JR103DWME Betriebsanleitung

NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
Adjusting the shoe
►Fig.5: ń.ăHОбăаrОЧМСă ă 2.ăHОбăЛШХtă ă 3.ăLШШsОЧ
АСОЧătСОăЛХКНОăХШsОsăТtsăМuttТЧРăОПiМТОЧМвăТЧăШЧОăЩХКМОă
along its cutting edge, reposition the shoe to utilize a
sСКrЩ,ăuЧusОНăЩШrtТШЧăШПăТtsăМuttТЧРăОНРО.ăTСТsăаТХХăСОХЩă
tШăХОЧРtСОЧătСОăХТПОăШПătСОăЛХКНО.
TШărОЩШsТtТШЧătСОăsСШО,ăХШШsОЧătСОăЛШХtăаТtСăСОбăаrОЧМС.ă
Slide the shoe to the desired position and then tighten
tСОăЛШХtăirЦХв.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the recipro/jig
saw blade
CAUTION: Always clean out all chips or foreign
matter adhering to the blade, blade clamp and/or
slider.ăFКТХurОătШăНШăsШăЦКвăМКusОăТЧsuПiМТОЧtătТРСtОЧ-
ТЧРăШПătСОăЛХКНО,ărОsuХtТЧРăТЧăКăsОrТШusăТЧУurв.
For Model JR103D
►Fig.6: ń.ăRОМТЩrШăsКаăЛХКНОă ă 2.ăBХКНОăМХКЦЩăsХООЯО
IЧsОrtătСОărОМТЩrШăsКаăЛХКНОăТЧtШătСОăЛХКНОăМХКЦЩăКsăПКră
КsăТtăаТХХăРШ.ăTСОăЛХКНОăМХКЦЩăsХООЯОărШtКtОsăКЧНăiбОsă
tСОărОМТЩrШăsКаăЛХКНО.ăMКФОăsurОătСКtătСОărОМТЩrШăsКаă
ЛХКНОăМКЧЧШtăЛОăОбtrКМtОНăОЯОЧătСШuРСăвШuătrвătШăЩuХХă
it out.
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation.ăTСТsăМКЧă
ЛОăОбtrОЦОХвăНКЧРОrШus.
NOTE:ăВШuăМКЧăЧШtăusОătСОăУТРăsКаăЛХКНОăаТtСă
JRńŃ3D.
►Fig.7: ń.ăRОМТЩrШăsКаăЛХКНОă ă 2.ăBХКНОăМХКЦЩăsХООЯО
TШărОЦШЯОătСОărОМТЩrШăsКаăЛХКНО,ărШtКtОătСОăЛХКНОă
МХКЦЩăsХООЯОăТЧătСОăНТrОМtТШЧăШПătСОăКrrШаăПuХХв.ăTСОărОМТ-
ЩrШăsКаăЛХКНОăТsărОЦШЯОНăКЧНătСОăЛХКНОăМХКЦЩăsХООЯОăТsă
iбОНăКtătСОărОХОКsОНăЩШsТtТШЧ.
NOTE:ăIПăвШuărОЦШЯОătСОărОМТЩrШăsКаăЛХКНОăаТtСШută
rШtКtТЧРătСОăЛХКНОăМХКЦЩăsХООЯОăПuХХв,ătСОăsХООЯОă
ЦКвăЧШtăЛОăiбОН.ăIЧătСТsăМКsО,ărШtКtОătСОăЛХКНОă
МХКЦЩăsХООЯОăПuХХв,ătСОЧăЦКФОătСОăsХООЯОăiбОНăКtătСОă
released position.
For Model JR105D
►Fig.8: 1. Hex wrench
4.ăTТРСtОЧ
►Fig.9: ń.ăRОМТЩrШăsКаăЛХКНОă ă 2.ăHОбăаrОЧМСă ă
3.ăHШХОăПШrărОМТЩrШăsКаăЛХКНОă ă 4.ăBХКНОăМХКЦЩ
2. Bolt 3. Loosen
TШăТЧstКХХătСОărОМТЩrШ/УТРăsКаăЛХКНО,ăХШШsОЧătСОăЛШХtăЛвă
СОбăаrОЧМС.ăАСОЧăТЧstКХХТЧРăКărОМТЩrШăsКаăЛХКНО,ăЩrОssă
tСОăЛШХtăаТtСătСОăСОбăаrОЧМСătШăШЩОЧătСОăsХШtăНurТЧРă
ТЧsОrtТЧРătСОăЛХКНО.
►Fig.10: ń.ăRОМТЩrШ/УТРăsКаăЛХКНОă ă 2.ăBХКНОăМХКЦЩă
3.ăHШХОăПШrărОМТЩrШăsКаăЛХКНОă ă 4.ăHШХОăПШrăУТРăsКаă
ЛХКНО
►Fig.11
ВШuăМКЧăusОăЛШtСăУТРăsКаăЛХКНОsă(BătвЩО)ăКЧНărОМТЩrШă
sКаăЛХКНОsăКММШrНТЧРătШăвШurăаШrФ.ăIЧsОrtătСОărОМТЩrШ/
УТРăsКаăЛХКНОăstrКТРСtăТЧtШătСОăЛХКНОăМХКЦЩăКЧНătТРСtОЧă
ТtăЛвăСОбăаrОЧМС.ăPuХХătСОărОМТЩrШ/УТРăsКаăЛХКНОăХТРСtХвătШă
ЦКФОăsurОătСКtătСОărОМТЩrШ/УТРăsКаăЛХКНОăНШОsăЧШtăПКХХăШППă
during operation.
TШărОЦШЯОătСОărОМТЩrШ/УТРăsКаăЛХКНО,ăПШХХШаătСОăТЧstКХХК-
tion procedure in reverse.
Hex wrench storage
►Fig.12: 1. Hex wrench
When not in use, store the hex wrench as shown in the
iРurОătШăФООЩăТtăПrШЦăЛОТЧРăХШst.

OPERATION

CAUTION: ůХаКвsăprОssătСОăsСШОăirЦХвă
against the workpiece during operation. If the
shoe is held away from the workpiece during opera-
tТШЧ,ăstrШЧРăЯТЛrКtТШЧăКЧН/ШrătаТstТЧРăаТХХăЛОăЩrШНuМОН,ă
МКusТЧРătСОăЛХКНОătШăsЧКЩăНКЧРОrШusХв.
CAUTION: Always wear gloves to protect your
СКЧНsăПrШЦăСШtălвТЧРăМСТpsăаСОЧăМuttТЧРăЦОtКХ.
CAUTION: Be sure to always wear suitable eye
protection which conforms with current national
standards.
CAUTION: ůХаКвsăusОăКăsuТtКЛХОăМШШХКЧtăĚМut-
tТЧРăШТХěăаСОЧăМuttТЧРăЦОtКХ. Failure to do so will
МКusОăЩrОЦКturОăЛХКНОăаОКr.
►Fig.13
PrОssătСОăsСШОăirЦХвăКРКТЧstătСОăаШrФЩТОМО.ăDШăЧШtă
КХХШаătСОătШШХătШăЛШuЧМО.ăBrТЧРătСОărОМТЩrШăsКаăЛХКНОă
into light contact with the workpiece. First, make a pilot
РrШШЯОăusТЧРăКăsХШаОrăsЩООН.ăTСОЧăusОăКăПКstОrăsЩООНă
to continue cutting.
►Fig.14
►Fig.15
You can use the switch lever or trigger according to your
work.
NOTE: If the tool is operated continuously until the
ЛКttОrвăМКrtrТНРОăСКsăНТsМСКrРОН,ăКХХШаătСОătШШХătШărОstă
ПШrăń5ăЦТЧutОsăЛОПШrОăЩrШМООНТЧРăаТtСăКăПrОsСăЛКttОrв.
2. Protrusion
ENGLISH 7