Herunterladen Inhalt Inhalt Diese Seite drucken

Sharp VC-G20SM Serviceanleitung Seite 16

Video cassette recorder
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

VC-G20SM/G200SM
VC-G201SM/G401SM
• Adjustment
1. If the indication of torque cassette meter is lower than
the setting, shift the tension spring engagement to the
part A.
2. If the indication of torque cassette meter is higher than
the setting, shift the tension spring engagement to the
part B.
A
B
Figure 4-18.
4-14 CHECKING THE BRAKE TORQUE
• Checking the brake torque at the supply side
Torque gauge
CCW
CCW: 4.41
CW:
4.12
Figure 4-19.
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at main PWB, plug in the power cord.
• Setting
1. Set a torque gauge to zero on the scale. Place it on the
supply reel disk.
2. Switch from the FF mode to the STOP mode.
3. Disconnect the power cord.
4. Please check Idler gear not contact with reel relay gear
(SU side)
• Checking
Turn the torque gauge at a rate of about one turn/2 sec
in the CW direction/CCW direction with respect to the
supply reel disk so that the reel disk and torque gauge
pointer rotate at equal speed, and make sure that the
value is within the setting (CW direction: 4.12 ±
+15
(42 gf·cm); CCW direction: 4.41 mN·m (45 15gf·cm).
–12
Tension arm
Tension spring
CW
Supply reel disk
±
+2.0
±
+20
mN⋅m (45
gf⋅cm)
–1.5
–15
±
+1.5
±
+15
mN⋅m (42
gf⋅cm)
–1.2
–12
+1.5
–1.2
+2.0
+20
–1.5
–15
• Checking the brake torque at the take-up side
Torque gauge
CW
Take-up reel
disk
CCW: 4.41
CW:
• Remove the cassette housing control assembly.
• After short-circuiting between TP803 and TP802
provided at main PWB, plug in the power cord.
• Setting
1. Switch from the FF mode to the STOP mode.
2. Disconnect the power cord.
3. Set a torque gauge to zero on the scale. Place it on the
take-up reel disk.
4. Please check Idler gear not contact with reel relay gear
(TU side)
• Checking
1. Turn the torque gauge at a rate of about one turn/2 sec
in the CCW direction/CW direction so that the reel disk
and torque gauge pointer rotates at equal speed and
make sure that the value is within the setting (CCW
direction: 4.41
+1.5
4.12
±
1.mN·m (42
–1.2
2. Adjustment of the brake torque at the supply side and the
take-up side
• Unless the supply side brake torque or take-up side
brake torque is within the setting, clean the felt surface
of reel disk (supply, take-up) brake lever, check again
the brake torque.
• If value cannot be set within the setting yet, replace the
main brake ass'y or main brake spring.
mN·m
16
CCW
+2.0
±
±
+20
mN⋅m (45
gf⋅cm)
–1.5
–15
+1.5
±
±
+15
4.12
mN⋅m (42
gf⋅cm)
–1.2
–12
Figure 4-20.
+2.0
+20
±
1mN·m (45
±
gf·cm), CW direction:
–1.5
–15
+15
to
gf·cm).
–12

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Vc-g200smVc-g201smVc-g401sm

Inhaltsverzeichnis