Emergency Lowering; Cable Operation For 2 Bed Sides; After-Sales Service; Limited Liability - Hulsta BOXSPRING Bedienungsanleitung

2.3.2 Emergency lowering

A mechanical emergency lowering device is installed so that the
unit can be lowered from the sitting position to the lying position in
the case of a power cut. Emergency mechanical lowering should be
carried out by 2 persons. Remove all bed linen, pillows, Topper units
Fig. 3 and mattresses.
Back section: person 1 raises the back section up to ca. 45°.
Person 2 bends down into the now open section of the Boxspring
bed and raises the plastic adjuster arm slightly, releasing the metal
drive lever from the adjuster arm. Person 2 leaves this area of the bed,
person 1 lowers the back section gently. Proceed in like manner to
replace the drive lever. Foot section: person 1 raises the end of the
foot section as far as possible. Continue as for the back section. When
lowering the foot section please ensure that the transverse bar rests
properly in its holder. Fig. 5/p. 22.
Fig. 4

2.3.3 Cable operation for 2 bed sides

With the aid of the Dual-Port synchronous cable 6P (ordered separately),
2 bed sides can be adjusted with one hand switch. It does not matter
which of the hand switches in the Dual-Port is used - they cannot be
used at the same time. The Dual-Port synchronous cable is inserted in
each of the hand switch jacks on the motors. The hand switches are
then inserted in the jacks in the Dual-Port synchronous cable. Fig. 6/p.
22.

2.4 After-sales service

The dealer from whom you bought the hülsta BOXSPRING bed is
your first contact person for service matters!
However, our customer advice team is ready to help you with technical
information (Tel. 0049 2563 86-0).
Furthermore, our personnel is always interested in any new information
and experience which result from use and may be valuable in helping
Fig. 5
us improve our products.

2.5 Limited liability

All details and notes in these instructions were put together in line with
currently valid norms and regulations, state-of-the-art technology and
our many years of knowledge and experience.
hülsta cannot accept any liability for damage caused by:
 Not observing these instructions
 Improper use
 Employment of non-qualified personnel
 Self-made conversions
 Technical alterations
 Use of impermissible spare parts
Fig. 6
25

3. Note

Sign Explanation
Only for use in dry rooms
Protective installations (Protection class II)
Declaration of conformity (product meets valid EU Guidelines)
"Waste of electrical and electronic equipment"
(WEEE Guideline regulates collection, separation and treatment of elec-
trical waste)

4. Troubleshooting

CAUTION
The repositioning function, which works without electricity, is not a
safety system in the sense of preventing danger.
Troubleshooting
This chapter contains measures which may be of help in the case of
malfunctioning. Should an error occur which is not listed in this table,
please get in touch with hülsta.
CAUTION
Troubleshooting and problem solving may only be carried out by a
qualified person who is qualified as an electrical machine fitter or has
a similar qualification.
The Problem Possible cause
No function in
No mains current
handswitch or drive
system.
Hand switch or drive system
defective.
For remote control
Batteries in hand transmitter
empty
Drives can suddenly Thermal switch on transfor-
no longer be moved.
mer may have tripped or be
defective.
Temperature fuse in transformer
tripped or defective.
Unit fuse possibly tripped or
defective.
No mains current
Lead (mains and / or hand
switch / extra drives) discon-
nected.
The electrical reposi-
No mains connection
tioning function does
not work.
Error in electronics
Cable handswitch
functions:
1
3
5
Meanings of buttons:
1 Back section "up"
2 Back section "down"
3 Foot section "up"
4 Foot section "down"
5 Central switching "up"
6 Central switching "down"
When pressed, the buttons
light up blue
Solution
Connect to mains source
Get in touch with your
supplier / dealer.
Exchange batteries
Leave the drive system inope-
rative for about 20 to 30 minutes.
Get in touch with your
supplier / dealer.
Get in touch with your
supplier / dealer.
Connect to mains source
Check lead and reconnect if
necessary.
Connect to mains source
Remove receiver plug and carry
out learning function
2
4
6
Fig. 7
26