General Power Tool Safety Warnings; Chain Saw Safety Warnings - Dolmar ES-33A Betriebsanleitung

................ First aid
........ Maximum permissible length of cut
....... Direction of chain travel
................ Chain oil
.................. Chain brake released
................. Chain brake applied
................ Prohibited!
............. Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that have
reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling
facility.
Intended use
The tool is intended for cutting lumbers and logs.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects to
the operation of other equipment. With a mains
impedance equal or less than 0.35 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
All manuals and user guides at all-guides.com

Chain saw safety warnings

1. Keep all parts of the body away from the saw
2. Always hold the chain saw with your right hand on
3. Hold the power tool by insulated gripping surfaces
4. Wear safety glasses and hearing protection.
5. Do not operate a chain saw in a tree. Operation of a
6. Always keep proper footing and operate the chain
ENE031-1
7. When cutting a limb that is under tension be alert
ENF002-1
8. Use extreme caution when cutting brush and
9. Carry the chain saw by the front handle with the
ENF100-1
10. Follow instructions for lubricating, chain
11. Keep handles dry, clean, and free from oil and
12. Cut wood only. Do not use chain saw for purposes
GEA010-1
13. Causes and operator prevention of kickback:
chain when the chain saw is operating. Before you
start the chain saw, make sure the saw chain is
not contacting anything. A moment of inattention
while operating chain saws may cause entanglement
of your clothing or body with the saw chain.
the rear handle and your left hand on the front
handle. Holding the chain saw with a reversed hand
configuration increases the risk of personal injury and
should never be done.
only, because the saw chain may contact hidden
wiring or its own cord. Saw chains contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate protective
clothing will reduce personal injury by flying debris or
accidental contact with the saw chain.
chain saw while up in a tree may result in personal
injury.
saw only when standing on fixed, secure and level
surface. Slippery or unstable surfaces such as
ladders may cause a loss of balance or control of the
chain saw.
for spring back. When the tension in the wood fibres
is released the spring loaded limb may strike the
operator and/or throw the chain saw out of control.
saplings. The slender material may catch the saw
chain and be whipped toward you or pull you off
balance.
chain saw switched off and away from your body.
When transporting or storing the chain saw
always fit the guide bar cover. Proper handling of
the chain saw will reduce the likelihood of accidental
contact with the moving saw chain.
tensioning and changing accessories. Improperly
tensioned or lubricated chain may either break or
increase the chance for kickback.
grease. Greasy, oily handles are slippery causing loss
of control.
not intended. For example: do not use chain saw
for cutting plastic, masonry or non-wood building
materials. Use of the chain saw for operations
different than intended could result in a hazardous
situation.
Kickback may occur when the nose or tip of the guide
bar touches an object, or when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden
reverse reaction, kicking the guide bar up and back
GEB072-1
9