Optional Accessories - Makita HM1213C Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für HM1213C:

Bedienungsanleitung (45 Seiten)

Betriebsanleitung (41 Seiten)

Betriebsanleitung (7 Seiten)

Seite von 36

/ 36
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

Indicator lamp

► Fig.3: 1. Power-ON indicator lamp (green)

2. Service indicator lamp (red)

The green power-ON indicator lamp lights up when the tool

is plugged. If the indicator lamp does not light up, the mains

cord or the controller may be malfunction. The indicator lamp

is lit but the tool does not start even if the tool is switched on,

the carbon brushes may be worn out, or the controller, the

motor or the ON/OFF switch may be malfunction.

The red service indicator lamp flickers up when the

carbon brushes are nearly worn out to indicate that the

tool needs servicing. After approx. 8 hours of use, the

motor will automatically be shut off.

ASSEMBLY

CAUTION:

•

Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

Side handle (auxiliary handle)

► Fig.4: 1. Side handle 2. Clamp nut

The side handle can be swung 360° on the vertical and

secured at any desired position. It also secures at eight

different positions back and forth on the horizontal.

Just loosen the clamp nut to swing the side handle to a

desired position. Then tighten the clamp nut securely.

The side handle also can be mounted in the rear

groove. Loosen the clamp nut and widen the side han-

dle base. Slide the side handle back to the rear groove

and secure it with the clamp nut.

Installing or removing the bit

► Fig.5: 1. Bit shank 2. Bit grease

Clean the bit shank and apply bit grease before install-

ing the bit.

Insert the bit into the tool. Turn the bit and push it in until

it engages.

► Fig.6: 1. Releasing cover

If the bit cannot be pushed in, remove the bit. Pull the

releasing cover down a couple of times. Then insert the

bit again. Turn the bit and push it in until it engages.

► Fig.7

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the releasing cover down all the

way and pull the bit out.

► Fig.8: 1. Releasing cover

Bit angle

► Fig.9: 1. Change ring

► Fig.10

The bit can be secured at 12 different angles. To

change the bit angle, slide the change ring forward,

then turn the change ring to change the bit angle. At the

desired angle, slide the change ring back to the original

position. The bit will be secured in place.

OPERATION

Chipping/Scaling/Demolition

► Fig.11

Always use the side grip (auxiliary handle) and firmly hold

the tool by both side grip and switch handle during oper-

ations. Turn the tool on and apply slight pressure on the

tool so that the tool will not bounce around, uncontrolled.

Pressing very hard on the tool will not increase the efficiency.

MAINTENANCE

CAUTION:

•

Always be sure that the tool is switched off and unplugged

before attempting to perform inspection or maintenance.

•

Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Lubrication

CAUTION:

•

This servicing should be performed by Makita

Authorized Service Centers only.

This tool requires no hourly or daily lubrication because it

has a grease-packed lubrication system. It should be relubri-

cated regularly. Send the complete tool to Makita Authorized

or Factory Service Center for this lubrication service.

To maintain product SAFETY and RELIABILITY, repairs, any

other maintenance or adjustment should be performed by Makita

Authorized Service Centers, always using Makita replacement parts.