Screwdriver Safety Warnings; Functional Description; Depth Adjustment - Makita FS2700 Bedienungsanleitung

Screwdriver safety warnings

1. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the fastener may contact hidden wiring or its
own cord. Fasteners contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Always be sure you have a firm footing.
2.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly.
3.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
6. Always secure workpiece in a vise or similar
hold-down device.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace strict
adherence to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
FUNCTIONAL
DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function
on the tool.

Depth adjustment

For Model FS2700 only
► Fig.1: 1. Locator 2. Front cap
When you wish to drive self drilling screws, etc., adjust
the depth as follows. Turn the locator to adjust the
depth.
Adjust the locator to create a distance of approximately
1 mm from the tip of the front cap (which works in
conjunction with the locator) to the base of the screw
head. One full turn of the locator equals 1 mm change
in depth.
► Fig.2
► Fig.3
Switch action
► Fig.4: 1. Switch trigger 2. Lock button
CAUTION:
• Before plugging in the tool, always check to see
that the switch trigger actuates properly and
returns to the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger and
then push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
NOTE:
• Even with the switch on and motor running, the
bit will not rotate until you fit the point of the bit
in the screw head and apply forward pressure to
engage the clutch.
Lighting up the lamps
► Fig.5: 1. Lamp
CAUTION:
• Do not look in the light or see the source of light
directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of
lamp. Be careful not to scratch the lens of lamp,
or it may lower the illumination.
Reversing switch action
► Fig.6: 1. Reversing switch lever
CAUTION:
• Always check the direction of rotation before
operation.
• Use the reversing switch only after the tool
comes to a complete stop. Changing the direc-
tion of rotation before the tool stops may dam-
age the tool.
This tool has a reversing switch to change the direc-
tion of rotation. Move the reversing switch lever
to the position (A side) for clockwise rotation or
the position (B side) for counterclockwise rotation.
Adjusting the fastening torque
When you wish to drive machine screws, wood screws,
hex bolts, etc. with the predetermined torque, adjust the
fastening torque as follows.
► Fig.7: 1. Adjusting ring 2. Pointer
The fastening torque may be adjusted by turning the adjust-
ing ring. The torque is increased by turning the adjusting
ring in the direction of the arrow and decreased by turning it
in the opposite direction. Align the number 1 on the adjust-
ing ring with the pointer on the gear housing. Drive a trial
screw into your material or a piece of duplicate material. If
the fastening torque is not suitable for the screw, continue
adjusting until the proper torque is obtained.
CAUTION:
• The adjusting ring should be turned only within
the numbered range. It should not be forced
beyond this range.
5 ENGLISH