Makita DLS713 Bedienungsanleitung Seite 19

Horizontal vise (optional accessory)
► Fig.36: 1. Vise knob 2. Projection 3. Vise shaft
4. Base
The horizontal vise can be installed on the left side of the base.
By turning the vise knob counterclockwise, the screw is released
and the vise shaft can be moved rapidly in and out. By turning
the vise knob clockwise, the screw remains secured. To grip the
workpiece, turn the vise knob gently clockwise until the projection
reaches its topmost position, then fasten securely. If the vise
knob is forced in or pulled out while being turned clockwise, the
projection may stop at an angle. In this case, turn the vise knob
back counterclockwise until the screw is released, before turning
again gently clockwise.
The maximum width of the workpiece which can be
secured by the horizontal vise is 120 mm.
WARNING:
• Grip the workpiece only when the projection is at
the topmost position. Failure to do so may result
in insufficient securing of the workpiece. This could
cause the workpiece to be thrown, cause damage
to the blade or cause the loss of control, which can
result in PERSONAL INJURY.
Holders and holder assembly
(optional accessories)
CAUTION:
For the tool equipped with the hold-
ers and the holder assemblies as standard acces-
sories, this type of use is not permitted due to the
country regulations.
► Fig.37: 1. Holder 2. Holder assembly
The holders and the holder assembly can be installed
on either side as a convenient means of supporting
workpieces horizontally. Install them as shown in the
figure. Then tighten the screws firmly to secure the
holders and the holder assembly.
When cutting long workpieces, use the holder-rod
assembly (optional accessory). It consists of two holder
assemblies and two rods 12.
► Fig.38: 1. Holder assembly 2. Rod 12
WARNING:
• Always support a long workpiece so it is
level with the top surface of the turn base for
an accurate cut and to prevent dangerous
loss of tool control. Proper workpiece support
will help avoid blade pinch and possible kick-
back which may result in serious personal injury.
OPERATION
NOTICE:
• Before use, be sure to release the handle from the
lowered position by pulling the stopper pin.
• Do not apply excessive pressure on the handle when
cutting. Too much force may result in overload of the motor
and/or decreased cutting efficiency. Push down handle with
only as much force as is necessary for smooth cutting and
without significant decrease in blade speed.
• Gently press down the handle to perform the cut. If
the handle is pressed down with force or if lateral
force is applied, the blade will vibrate and leave a
mark (saw mark) in the workpiece and the preci-
sion of the cut will be impaired.
• During a slide cut, gently push the carriage toward
the guide fence without stopping. If the carriage
movement is stopped during the cut, a mark will
be left in the workpiece and the precision of the
cut will be impaired.
WARNING:
• Make sure the blade is not contacting the
workpiece, etc. before the switch is turned
on.
Turning the tool on with the blade in contact with
the workpiece may result in kickback and seri-
ous personal injury.
Press cutting (cutting small
workpieces)
► Fig.39: 1. Thumb screw 2. Holder assembly
Workpieces up to 52 mm high and 97 mm wide
can be cut in the following manner.
Push the carriage toward the guide fence fully and
tighten two clamp screws which secure the slide
poles clockwise to secure the carriage. Secure the
workpiece with the proper type of vise. Switch on
the tool without the blade making any contact and
wait until the blade attains full speed before lower-
ing. Then gently lower the handle to the fully low-
ered position to cut the workpiece. When the cut
is completed, switch off the tool and WAIT UNTIL
THE BLADE HAS COME TO A COMPLETE STOP
before returning the blade to its fully elevated
position.
WARNING:
• Firmly tighten two clamping screws which
secure the slide poles clockwise so that the
carriage will not move during operation.
Insufficient tightening of the locking screw may
cause possible kickback which may result in
serious personal injury.
Slide (push) cutting (cutting wide
workpieces)
► Fig.40: 1. Thumb screw 2. Holder assembly
Loosen two clamp screws which secure the slide poles
counterclockwise so that the carriage can slide freely.
Secure the workpiece with the proper type of vise. Pull
the carriage toward you fully. Switch on the tool without
the blade making any contact and wait until the blade
attains full speed. Press the handle down and PUSH
THE CARRIAGE TOWARD THE GUIDE FENCE AND
THROUGH THE WORKPIECE. When the cut is com-
pleted, switch off the tool and WAIT UNTIL THE BLADE
HAS COME TO A COMPLETE STOP before returning
the blade to its fully elevated position.
19 ENGLISH