Optional Accessories - Makita BO6030 Bedienungsanleitung

Emptying dust bag
► Fig.7: 1. Dust nozzle 2. Push button
► Fig.8: 1. Hook 2. Dust nozzle 3. Dust bag 4. Push button
When the dust bag is about half full, switch off and
unplug the tool. Hold the tool and remove the dust bag
from the dust nozzle while pressing the push button.
After emptying the dust bag, insert the hook on the dust
nozzle into the rectangular hole on one side of the dust
bag frame and push up the dust bag frame until it clicks
into place on the push button.
► Fig.9
Installing paper dust bag (optional
accessory)
► Fig.10: 1. Groove 2. Front fixing cardboard 3. Front
side of paper dust bag
Place the paper dust bag on the paper dust bag holder with
its front side upward. Insert the front fixing cardboard of the
paper dust bag into the groove of the paper dust bag holder.
Then press the upper part of the front fixing cardboard
in arrow direction to hook it onto the claws.
► Fig.11: 1. Claws 2. Upper part
Insert the notch of the paper dust bag into the guide of
the paper dust bag holder. Then install the paper dust
bag holder set on the tool.
► Fig.12: 1. Notch 2. Guide
► Fig.13
OPERATION
Sanding operation
► Fig.14
CAUTION:
• Never switch on the tool when it is in contact with
the workpiece, it may cause an injury to operator.
• Never run the tool without the abrasive disc. You
may seriously damage the pad.
• Never force the tool. Excessive pressure may
decrease the sanding efficiency, damage the
abrasive disc or shorten tool life.
Hold the tool firmly. Turn the tool on and wait until it
attains full speed. Then gently place the tool on the
workpiece surface. Keep the pad flush with the work-
piece and apply slight pressure on the tool.
Polishing operation
CAUTION:
• Use only a Makita genuine sponge pad, felt pad
or wool pad (optional accessories).
• Always operate the tool at low speed to prevent
work surfaces from damage/burning.
• Never force the tool. Excessive pressure may
decrease the polishing efficiency and cause
motor overload, resulting in tool malfunction.
1. Applying wax
► Fig.15: 1. Sponge pad
Use an optional sponge pad. Apply wax to the sponge pad or
work surface. Run the tool at low speed to smooth out wax.
NOTE:
• First, wax a non critical portion of the work sur-
face to make sure that the tool will not scratch
the surface or result in uneven waxing.
2. Removing wax
► Fig.16: 1. Felt pad
Use an optional felt pad. Run the tool at low speed
to remove wax.
3. Polishing
► Fig.17: 1. Wool pad
Use an optional wool pad. Run the tool at low speed
and apply the wool pad gently to the work surface.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and unplugged
before attempting to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs, car-
bon brush inspection and replacement, any other maintenance
or adjustment should be performed by Makita Authorized
Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recom-
mended for use with your Makita tool specified
in this manual. The use of any other accessories
or attachments might present a risk of injury to
persons. Only use accessory or attachment for
its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Hook-and-loop type abrasive discs (with pre-punched holes)
• Hook-and-loop type sponge pad
• Hook-and-loop type felt pad
• Hook-and-loop type wool pad
• Sanding cloth
• Paper dust bag
• Paper dust bag holder
• Pad 150
NOTE:
• Some items in the list may be included in the
tool package as standard accessories. They
may differ from country to country.
7 ENGLISH