Additional Safety Instructions - Ferm TSM1033 Übersetzung Des Original Betriebsanleitung

Additional safety instructions

1. When using the saw blades with hard metal
teeth (Carbon tipped) it is advisable to use
blades with a negative or slightly positive cutting
angle. Do not use any saw blades with deeply
cut teeth. They can grip the protective cap.
2. Attention: First carefully assemble all the parts
before starting work. Follow the procedure as
indicated.
3. If you are not familiar with using such a machine,
you would be better to be informed first by a
professional, an instructor or by a technician.
4. Always clamp or press the workpiece firmly
against the saw guide, before you carry out the
process. The use of all possible clamping set-
ups is preferable to using your hands.
5. Important: If you are holding the workpiece by
hand for the process to be carried out, keep
a minimum distance of 100 mm from the saw
blade.
6. Always press the workpiece against the bench.
7. Keep the saw blade sharp and check regularly
whether it rotates freely without abnormal
vibrations. Replace the saw blade if necessary.
8. Allow the machine to rotate freely until it
reaches the maximum number of revolutions,
before you start the process.
9. Maintain the air inlets at the back and the
bottom of the bench saw machine and electric
motor for a longer machine life. Dust piles
must be removed.
10. A lways lock the different degree set-ups
before you start processing.
11. Only buy suitable saw blades with a number
of revolutions of at least 6000 revolutions per
minute.
12. Only use the correct saw blade. Too small or
too big saw blades are extremely dangerous.
13. Regularly inspect the saw blade for any faults.
Replace the saw blade if necessary.
14. Grease the new saw blade and clean the
flanges before you assemble the new blade.
Then assemble the blade in the correct
direction and pull the flanges firmly using the
central bolt.
15. Only use original flanges. All other types are
not suitable.
16. Never work without the protective cap of the
saw blade.
17. The moving part of the protective cap must
also remain assembled.
8
All manuals and user guides at all-guides.com
18. Never grease the saw blade while it is rotating.
19. Always keep your hands removed from the
20. Never pick up the workpiece by grasping with
21. Ensure that the workpiece never touches
22. Never process metal or stone sorts with this
23. U se support aids in order to support long
24. Never use the machine in a dangerous
25. Never leave the machine unattended without
26. If you hear abnormal noises, try to trace them
27. If a part is broken or damaged, replace it or
28. Never stand in the track of the saw blade but
29. Y our hands must likewise be placed next to
30. Always use the push stick instead of your
31. Always place the wood at the front of the saw
32. For mitring only the adjustable guide must be
33. Never use the fence as a linear measure for
34. If the saw blade is locked: first switch off the
35. Avoid workpieces hitting back in your direction
36. Before you continue sawing, ensure that you
37. Never use thinners to clean the machine. Only
38. D o not use saw blades which are damaged or
track of the saw blades.
your hands along or behind the saw blade.
the saw blade before the machine has been
switched on.
machine.
workpieces.
environment, where inflammable gases or
fluids are present.
first disconnecting it from the mains voltage.
or take the machine to a recognized fitter, or
repair company.
repair it immediately.
stand to the left or the right of the saw bench.
the track of the saw blade.
hands to push the wood through the saw.
bench and then push it further back.
used and the fence must be removed. (Fig. J)
cutting off beams.
machine before you attend to the fault.
by taking the following measures:
• A lways use sharp saw blades.
• D o not saw too small workpieces.
• N ever release the workpiece before it has
been completely pushed through the saw.
• A lways adjust the guide parallel to the saw
blade.
• N ever remove the saw protection.
are standing firmly and that your hands are in
the required position.
use a damp cloth for cleaning.