Herunterladen Inhalt Inhalt Diese Seite drucken

Maintenance; Optional Accessories - Makita CV100D Betriebsanleitung

Akku-thermojacke
Vorschau ausblenden Andere Handbücher für CV100D:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 11
ASSEMBLY
CAUTION:
• Hold the battery holder and the battery cartridge
firmly when installing or removing battery
cartridge. Failure to hold the battery holder and the
battery cartridge firmly may cause them to slip off your
hands and result in damage to the battery holder and
battery cartridge and a personal injury.
Installing or removing battery cartridge to
the battery holder (Fig. 2)
for CV100D
To install the battery cartridge (5), hold it so that the
battery cartridge front shape fits to that of the battery
holder opening and slip it into place. Insert it all the way
until it locks in place with a little click.
Always insert the battery cartridge all the way until it locks
in place. If not, it may accidentally fall out of the battery
holder, causing injury to you or someone around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, withdraw it from the
battery holder while pressing the buttons (6) on both sides
of the cartridge.
for DCV200
To install the battery cartridge (7), align the tongue on the
battery cartridge with the groove in the battery holder and
slip it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator (8) on the
upper side of the button, it is not locked completely.
Always install the battery cartridge fully until the red
indicator cannot be seen. If not, it may accidentally fall out
of the battery holder, causing injury to you or someone
around you.
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
To remove the battery cartridge, slide it from the battery
holder while sliding the button (9) on the front of the
cartridge.
Attaching the battery holder to the heated
vest
for CV100D (Fig. 3)
Connect the battery holder and the power cable of the
vest. Place the battery holder in the battery holder pocket.
for DCV200 (Fig. 4)
You can hang the battery holder on the belt.
Firstly pass the vest's power cable through the hole inside
the battery holder pocket, and connect the battery holder
and the power cable of the vest. And then hang the
battery holder on your belt.
Connecting USB device (For DCV200
only) (Fig. 5)
CAUTION:
• Connect only devices which are compatible with DC5V,
2.1A power source to the USB power supply port.
Otherwise it may cause malfunction to the battery
holder.
The battery holder (with the battery) can work as an
external power supply for USB device. Connect the USB
cable (not included) with the power supply port of the
battery holder. And then connect the other end of the
cable with the device. The USB cable can be placed
inside the vest for convenience by using the hole of the
pocket and cable holder.
NOTE:
• Before connecting USB device to the charger, always
backup your data of USB device. Otherwise your data
may lose by any possibility.
• The charger may not supply power to some USB
devices.
• Wait for 10 seconds before charging another device
consecutively.
• When not using or after charging, remove the USB
cable and close the cover.

MAINTENANCE

CAUTION:
Always be sure that the vest is switched off and the
battery cartridge is removed before attempting to perform
inspection or maintenance.
If vest does not switch on or any fault is found with a fully
charged battery cartridge, clean the terminals of the
battery holder and the battery cartridge. If vest still does
not work properly, stop using the vest and contact our
authorized service center.

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments are recommended for
use with your Makita tool specified in this manual. The use
of any other accessories or attachments might present a
risk of injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
package as standard accessories. They may differ from
country to country.
5

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dcv200Dcv200zmDcv200zxlDcv200zl

Inhaltsverzeichnis