Connecting Usb Devices; Maintenance; Optional Accessories - Makita CJ105D Betriebsanleitung

Battery protection system
The device is equipped with a battery protection system. This
system automatically cuts off power to the heating parts to
extend battery life. If the remaining battery capacity is too low,
the device will not operate. When you turn the device on, the
power is supplied to the heating parts again, but stops soon.
In this situation, remove and recharge the battery cartridge.

Connecting USB devices

CAUTION:
Connect only devices that are
compatible with the USB power supply port. Not
doing so may cause a malfunction of the battery
holder.
NOTICE:
Before connecting a USB device to
the battery holder (with the battery), always back
up the data on the USB device. Not doing so may
cause a loss of your data.
The battery holder (with the battery cartridge) can work
as an external power supply for USB devices.
Open the cover and connect a USB cable (not included)
to the power supply port of the battery holder. Then con-
nect the other end of the cable to the device and turn on
the switch next to the USB port.
The battery holder (with the battery cartridge) supplies
DC 5 V, 2.4 A (maximum).
► Fig.13: 1. Cover 2. Switch
The USB cable can be placed inside the jacket or vest
for convenience using the hole in the pocket and the
cable holder.
For CJ105D / DCJ205 / CJ106D / DCJ206
► Fig.14: 1. USB cable
For CV102D / DCV202
► Fig.15: 1. USB cable
NOTE: The battery holder may not supply power to
some USB devices.
NOTE: When not in use or after charging, remove the
USB cable and close the cover.
NOTE: Battery power is consumed while the switch is
turned on. Always turn off the switch when not in use.
NOTE: When charging multiple USB devices in suc-
cession, wait about 10 seconds after charging of the
previous device has completed before beginning to
charge the next device.

MAINTENANCE

CAUTION:
Always be sure that the jacket is
switched off and the battery cartridge is removed before
attempting to perform inspections or maintenance.
CAUTION:
If the jacket does not switch on
or any fault is found with a fully charged battery
cartridge, clean the terminals of the battery holder
and the battery cartridge. If the jacket still does
not work properly, stop using the jacket and con-
tact our authorized service center.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Cleaning the jacket or vest
For all models
• Detach the battery holder from the jacket or vest
before washing.
• Follow the instructions on the tag.
• Do not wash the jacket or vest with other clothes.
Doing so may cause color fading or color transfer.
• Use a laundry net when using a washing machine.
• Do not use the fabric softener.
• Use only neutral detergent.
• After washing, take out the jacket or vest from
washing machine at once.
• Be sure to close the zip fastener before washing.
For CJ106D / DCJ206 only
• The performance of light reflector parts may be
weakened by washing.
• Machine wash in gentle cycle (The number of
times for washing is up to 25 times.)
• The number of times for washing is not the only
the factor to decide the lifetime of the jacket.
• The life of the jacket changes by how to use, how
to care and store state.
• If the light reflector parts or clothes have been
deteriorated, replace to a new jacket.
OPTIONAL
ACCESSORIES
CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regard-
ing these accessories, ask your local Makita Service
Center.
• Battery holder
• Makita genuine battery and charger
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
11 ENGLISH