Protecting The Environment; Re-Sharpening The Blades - DeWalt D27300 Originalanweisungen

EngLIsH
MAINTENANCE
Your D WALT power tool has been designed to operate over a long period of time with a
e
minimum of maintenance. Continuous satisfactory operation depends upon proper tool care
and regular cleaning.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. Be sure the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Replacing the Blades (Fig. R1, R2)
The machine is equipped with a cutterhead that holds two blades.

WARNING: Always replace the blades simultaneously.

WARNING: Be aware the cutting blades shall be replaced in the described way only.
Never fit cutting blades other than the ones recommended.

WARNING: Sharp edges.

WARNING: Wear gloves when replacing the blades.

WARNING: Prior to replacing the blades always unplug the machine.
Removing the Blades
1. Remove the fence and the guard.
2. Carefully rotate the cutterhead 57 until the first blade becomes visible.
3. Loosen the bolts 58 using the spanner supplied.
4. Lift the blade assembly 59 out of the cutterhead. Use a pair of pliers if necessary.
5. Take the blade from the holder
60 61
6. Repeat as for the other blade.
Fitting the Blades
1. Attach the blade 60 to the blade holder
in notches 63 .
2. Re-fit the assembly into the cutterhead
3. Adjust the blade as described below.
4. Tighten the bolts 58 (torque: 6–8 Nm).
5. Repeat as for the other blade.
Adjusting the Blades (Fig. R3)
1. Check the position of the blade at both ends.
60
2. Position the gauge 64 over the cutterhead
3. The bottom edge of the gauge must coincide with the tip of the blade
4. If adjustment is required, proceed as follows:
- Turn each adjusting screw 65 in or out as necessary until the blade tip coincides with
the gauge.

Re-sharpening the Blades

The blades can be re-sharpened at 42°.

WARNING: The blades can be re-sharpened max. 3 mm down from their original size. If
the blade size has decreased by more than 3 mm, the blades have to be replaced.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Before use, carefully check the cutter-head to determine that it will operate properly. Ensure
that resin or workpiece particles cannot lead to blockage of one of the functions.
Thicknessing mode: In case of workpiece fragments jammed between cutter-head and in-feed
roller, disconnect the machine from the power supply and remove the jammed parts.
Keep the ventilation slots clear and regularly clean the housing with a soft cloth.
• Keep the tables clean and free from grease. Regularly apply some wax to the tables.
• Keep the machine free from dust and shavings.
• On a daily basis, check and clean the kickback and feed spindles.
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
These include spare cutting blades (DE7333).
Consult your dealer for further information on the appropriate accessories.
22
.
61 . Make sure that the outer bolt heads
.
57
57 as shown.
60 .
WALT, have not been tested
e

Protecting the Environment

Separate collection. Products and batteries marked with this symbol must not be
disposed of with normal household waste.
Products and batteries contain materials that can be recovered or recycled reducing
the demand for raw materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at www.2helpU.com.
62 fall