Toolson KGZ3400 Originalanleitung Seite 17

Compound Cut
• A compound cut is a combination of mitre cut and
bevel cut. Refer to the above procedures to perform
this cut.
Base Moulding
• Base moulding can be cut vertically against fence or
flat on the table. Follow the table below for reference.
Settings Vertical position
(Back of moulding is
flat against the fence)
Extension fence Close to the blade
Bevel angle 0°
Moulding position Left side Right side
Inside Mitre Left at 45° Right at
corner angle 45°
Moulding Bottom Bottom
position against against
table table
Finished Keep left Keep right
side side of side of
cut cut
Outside Mitre Right at Left at 45°
corner angle 45°
Moulding Bottom Bottom
position against against
table table
Finished Keep left Keep right
side side of side of
cut cut
Crown Moulding Cut
• Crown moulding can only be cut flat on the table us-
ing this mitre saw.
• This mitre saw has special mitre stops of 31.6° left
and right and a bevel stop of 33.9° for a special crown
moulding 1 i.e. 52° between the back of the moulding
and the top flat surface that fits against the ceiling; 38°
between the back of the moulding and the bottom flat
surface that fits against the wall. Refer to the following
table for this crown moulding cut.
Settings Left side
Inside corner Mitre angle 30° right
Bevel angle 33,9°
Moulding Top against
position fence
Finished side Keep left side
of cut
Outside corner Mitre angle 30° left
Bevel angle 33,9°
Moulding Bottom against
position fence
Finished side Keep right side
of cut
Note:
• These special stops cannot be used with 45° crown
moulding.
• Since most rooms do not have angles of exactly 90°,
fine tuning is needed and always take a test cut to
confirm the correct angles.
Horizontal position
(Back of moulding is
flat on the table)
Far from the blade
45°
Left side Right side
0° 0°
Top Bottom
against against
fence fence
Keep left Keep left
side of side of
cut cut
0° 0°
Bottom Top
against against
fence fence
Keep right Keep right
side of side of
cut cut
Right side
30° left
33,9°
Bottom against
fence
Keep left side
of cut
30° left
33,9°
Top against
fence
Keep right side
of cut
Pullover Cut
WARNING:
1. Never pull the cutting head assembly and spinning
blade towards you during the cut. The blade may try
to climb up on the top of the workpiece, causing the
cutting head assembly and spinning blade to kick
back.
2. Never lower the spinning saw blade down before
pulling the cutting head to the front of the saw.
• Unlock the carriage 1 with the lock handle 2 and al-
low the cutting head assembly to move freely. (Fig. 6)
• Move the mitre handle and cutting head to the desired
mitre angle and bevel angle according to the mitre cut
and bevel cut procedures.
• Grasp the saw handle and pull the carriage forward
until the centre of the saw blade is over the front of
the work piece.
• Activate the switch, then press the blade guard lock
lever to lower the cutting head down.
• When the saw reaches full speed, push the saw han-
dle down slowly, cutting through the leading edge of
the workpiece.
• Slowly move the saw handle toward the fence, com-
pleting the cut.
• Release the switch and allow the blade to stop spin-
ning before allowing the cutting head to raise.
Depth adjustment normal Fig. 6.1
Sawing function 5 mm below the table top. (separate
work pieces.)
Depth stop (1) housing-adjacent.
Stop screw (2) is used.
Setscrew (3) has no function.
Depth adjustment variable Fig.
Sawing function above the table top. (covered cuts)
Set depth stop (1) to the outside.
Set the setscrew (3) to the desired measurement and se-
cure it with the counternut (4).
Make a test cut.
Stop screw (2) is not used.
Carrying the Tool
• Loosen the mitre lock knob and turn the table all the
way to the right. Lock the table at 45° mitre angle.
• Push the cutting head backwards and lock the car-
riage.
• Lower the cutting head and push in the lock pin.
• Carry this mitre saw with the built-in carry handle and
the side of the base.
Replacing of the saw blades, Fig. 7
Warning: Before replacing saw blades the switch
must be turned off and the mains plug must be dis-
connected from the mains socket in order to avoid
injuries by accidental start up of the machine.
• Disconnect the mains plug.
• Set the sawing unit to position "mitre operation".
17 І 180