General Notes - Toolson KGZ3400 Originalanleitung

Manufacturer:
Scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
we wish you a pleasant and successful working experi-
ence with your new TOOLSON machine.
Advice:
According to the applicable product liability law the man-
ufacturer of this device is not liable for damages which
arise on or in connection with this device in case of:
• improper handling,
• non-compliance with the instructions for use,
• repairs by third party, non authorized skilled workers,
• installation and replacement of non-original spare
parts,
• improper use,
• failures of the electrical system due to the non-com-
pliance with the electrical specifications and the
VDE 0100, DIN 57113 / VDE 0113 regulations
Recommendations:
Read the entire text of the operating instructions prior to
the assembly and operation of the device.
These operating instructions are intended to make it
easier for you to get familiar with your device and utilize
its intended possibilities of use.
The operating instructions contain important notes on
how to work safely, properly and economically with your
machine and how to avoid dangers, save repair costs,
reduce downtime, and increase the reliability and work-
ing life of the machine.
In addition to the safety regulations contained herein,
you must in any case comply with the applicable regula-
tions of your country with respect to the operation of the
machine.
Put the operating instructions in a clear plastic folder to
protect them from dirt and humidity, and store them near
the machine. The instructions must be read and care-
fully observed by each operator prior to starting the work.
Only persons who have been trained in the use of the
machine and have been informed on the related dangers
and risks are allowed to use the machine. The required
minimum age must be met.
In addition to the safety notes contained in the present
operating instructions and the special regulations of your
country, the generally recognized technical rules for the
operation of wood working machines must be observed.
Know your Pullover Mitre Saw (Fig. 1)
1 Pullover carriage
2 Upper blade guard
3 Lower blade guard lock lever
4 Trigger switch
5 Handle
6 Motor
7 Lower blade guard
8 Tungsten Carbide Tipped blade
9
Fence
10 Extension support (optional)
11 Mitre scale
12 Arrester
13 Table insert
14 Turn table
15 Bolt holes
16 Base
17 Clamp
18 Dust bag
19 Handle
20 Laser
21 Table clamping handle
Technical data
ø blade
ø bore
Dimensions 810 x 460 x 355 mm
Weight
ø turn table
Mitre stops left
0°, 15°, 22,5°, 30°, 45°
and right
Pivoting range
Inclination
range
Max. Capacity
Cross cut at
90°
Mitre cut at 45°
Becel cut at
45°
Compound cut
at 45°
Drive
Motor V/Hz
Consumption
1500 W (S6 25%)
power P1
No load speed
Laser class
Subject to technical changes!
The noise levels of this machine during cutting are
as follows:
Noise level during working
L :99,6dB(A) K=3dB(A)
pA
L :112,6dB(A) K=3dB(A)
wA
Vibration:
Vibration: 4,51m/s
2
K=1.5m/s
2

General Notes

• When you unpack the device, check all parts for pos-
sible transport damages. In case of complaints the
supplier is to be informed immediately. Complaints re-
ceived at a later date will not be acknow ledged.
210 mm
30,0 mm
13,5 kg
250 mm
-45°/0°/45°
0°–45°
58 x 340 mm
58 x 240 mm
32 x 340 mm
32 x 240 mm
230V / 50 Hz
5000 1/min
2
13 І 180