Kenwood FDP60 Bedienungsanleitungen Seite 13

cs
citrus juicer
(if supplied)
Use the citrus juicer to squeeze the juice from citrus fruits
(eg oranges, lemons, limes and grapefruits).
cone
sieve
to use the citrus juicer
1 Fit the bowl onto the power unit, add the detachable drive
shaft.
2 Fit the sieve into the bowl - ensuring the sieve handle is
locked into position directly over the bowl handle
3 Place the cone over the drive shaft turning until it drops all
bt
the way down .
4 Cut the fruit in half. Then switch on and press the fruit onto
the cone.
l
The citrus juicer will not operate if the sieve is
not locked correctly.
l
For best results store and juice the fruit at room temperature
and hand roll on a worktop before juicing.
l
To help with juice extraction move the fruit from side to side
when juicing.
l
When juicing large quantities, empty the strainer regularly to
prevent the build up of pulp and seeds.
ct
juice extractor
Use the centrifugal juicer for making juice from firm fruit and
vegetables.
safety
l
Do not use the juice extractor if the filter is
damaged.
l
Only use the pusher supplied. Never put your fingers in the
feed tube. Unplug before unblocking the feed tube.
l
Before removing the lid, switch off and wait for the filter to
stop.
l
Never use a damaged attachment.
pusher
lid
pulp remover
filter drum
to use the juice extractor
1 Fit the bowl to the power unit
2 Place the pulp remover into the filter drum - ensuring the
tabs locate with the slots in the bottom of the drum
cm
3 Fit the filter drum .
4 Place the attachment lid onto the bowl, turn until it locks and
the feed tube sits over the handle
extractor will not operate if the bowl or lid are
not fitted correctly into the interlock.
5 Cut the food to fit the feed tube.
6 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube. Process fully before
adding more.
l
After adding the last piece, let the juice extractor run for a
further 30 seconds to extract all the juice from the filter
drum.
bs
.
(if supplied)
ck
.
cl
cn
. Your juice
important
l
If the juice extractor starts to vibrate, switch off and empty
the pulp from the drum. (The juice extractor vibrates if the
pulp becomes unevenly distributed).
l
Maximum capacity that can be processed at one time is
800g of fruit or vegetables (refer to speed chart).
l
Some very hard foods may make your juice extractor slow
down or stop. If this happens switch off and unblock the
filter.
l
Switch off and clear the pulp collector regularly during use.
hints
l
Before processing remove stones and pips (eg pepper,
melon, plum) and tough skins (eg melon, pineapple). You
don't need to peel or core apples and pears.
l
Use firm, fresh fruit and vegetables.
l
To maximise juice extraction place small quantities at a time
in the feed tube and push down slowly.
l
Citrus fruit - peel and remove the white pith, otherwise the
juice may taste bitter. For best results use the citrus juicer.
care & cleaning
l
Always switch off and unplug before cleaning.
l
Handle the blades and cutting discs with care -
they are extremely sharp.
l
Some foods may discolour the plastic. This is perfectly
normal and won't harm the plastic or affect the flavour of
your food. Rub with a cloth dipped in vegetable oil to
remove the discolouration.
power unit
l
Wipe with a damp cloth, then dry. Ensure that the interlock
area is clear of food debris.
l
Don't immerse the power unit in water.
l
Store excess cord in the storage area at the back of the
power unit
blender
1 Empty the goblet, unscrew the blade unit by turning to the
unlock position
pushing up from underneath.
l
Care should be taken when removing the blade unit from
the base.
2 Wash the goblet by hand.
3 Remove and wash the seal.
4 Don't touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don't
immerse the blade unit in water.
5 Leave to dry upside down.
dual whisk
.
l
Detach the beaters from the drive head by gently pulling
them free. Wash in warm soapy water.
l
Wipe the drive head with a damp cloth, then dry. Do not
immerse the drive head in water.
grinding mill
l
Remove the blade assembly from the jar by turning in an
anti-clockwise direction.
l
Wash the jar by hand.
l
Don't touch the sharp blades – brush them clean using hot
soapy water, then rinse thoroughly under the tap. Don't
immerse the blade unit in water.
l
Leave to dry upside down.
11
cq
.
to release. Then remove the blade unit by