Storage; Electrical Connection; Disposal And Recycling - Scheppach PM1200 Original Bedienungsanleitung

Service information
Please note that the following parts of this product
are subject to normal or natural wear and tear, and
are therefore also required as consumables.
Wear parts*: Carbon brush, mixing rod
* Not necessarily included in the scope of delivery!

11. Storage

• The whole machine and all accessories must be
thoroughly cleaned.
• Store devices and accessories out of the reach
of children in a dark and dry place above freez-
ing point. The optimum storage temperature lies
between 5 and 30 °C. Store the power tool in its
original packaging.
• Do not wrap the machine into bags or covers made
of nylon or plastic, as dampness may develop.

12. Electrical connection

m The electric motor installed is connected and
ready for operation.
The connection complies with the applicable VDE
and DIN provisions.
The customer's mains power connection as well
as the extension lead used must also comply
with these regulations and the local electricity
supplier regulations.
Damaged electrical connection cables
The insulation on electrical connection cables is of-
ten damaged.
Possible causes:
• Pressure points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insulation
damage.
Check the electrical connection cables for damage
regularly. Ensure that the connection cables are dis-
connected from electrical power when checking for
damage. Electrical connection cables must comply
with the applicable VDE and DIN provisions, and the
local power supply regulations. Only use connection
cables marked with H07RN. The printing of the type
designation on the connection cable is mandatory.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
AC motor
• The mains voltage must be 220÷240 V/50 Hz.
• Extension leads up to 25 m long must have a mini-
mum cross section of 1.5 mm², and over 25 m long
must have a minimum cross section of 2.5 mm².
• The mains connection must be protected with a
max. 16 A fuse.
Connections and repair work on the electrical
equipment may only be carried out by electri-
cians.
Please provide the following information in the event
of any enquiries:
• Engine manufacturer; engine type
• Type of current for the motor
• Data of machine type plate
• Electrical control data

13. Disposal and recycling

The device is supplied in packaging to avoid transport
damages. This packaging is raw material and can
thus be used again or can be reintegrated into the
raw material cycle. The device and its accessories
are made of different materials, such as metals and
plastics. Take defective components to special waste
disposal sites. Check with your specialist dealer or
municipal administration!
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and
electronic equipment (WEEE). This product must be
handed over at the intended collection point. This can
be done, for example, by returning it when purchasing
a similar product or delivering it to an authorised col-
lection point for the recycling of old electrical and
electronic devices. Improper handling of waste equip-
ment may have negative consequences for the envi-
ronment and human health due to potentially hazard-
ous substances that are often contained in electrical
and electronic equipment. By properly disposing of
this product, you are also contributing to the effective
use of natural resources. You can obtain information
on collection points for waste equipment from your
municipal administration, public waste disposal au-
thority, an authorised body for the disposal of waste
electrical and electronic equipment or your waste dis-
posal company.