Makita DCC500 Betriebsanleitung Seite 17

2. Unscrew the water supply cap attached to the
water supply tank.
► Fig.23: 1. Water supply cap 2. Water outlet
NOTICE:
Be careful not to lose the rubber washer
placed at the bottom of the water supply cap when-
ever you reassemble the cap.
3.
Attach the water supply cap onto the cap plug of
the hose.
► Fig.24: 1. Water supply cap 2. Cap plug
4. Insert the hose with the water supply cap pointing
downwards into the water supply holder until it locks
with a click.
► Fig.25: 1. Water supply cap 2. Water supply holder
Disconnecting from the mains water
supply
1. Set the water supply lever on the wheel cover in
the "OFF" (O) position and turn the water off.
2.
Press the eject button to release the water supply
hose, and then pull the hose off.
► Fig.26: 1. Eject button
3.
Remove the water supply plug from the supply
water outlet.
OPERATION
CAUTION:
THIS TOOL SHOULD ONLY BE
USED ON HORIZONTAL SURFACES.
CAUTION:
Be sure to move the tool forward
in a straight line and gently. Forcing and exerting
excessive pressure or allowing the wheel to bend,
pinch or twist in the cut can cause overheating of the
motor and dangerous kickback of the tool.
Hold the tool firmly. Set the base plate on the workpiece
to be cut without the diamond wheel making any con-
tact. Then turn the tool on and wait until the diamond
wheel attains full speed. Now simply move the tool
forward over the workpiece surface, keeping it flat and
advancing smoothly until the cutting is completed. Keep
your cutting line straight and your speed of advance
uniform.
Straight cutting
► Fig.27
45° bevel cutting
► Fig.28
Wet cutting operations
Install the optional water supply cover and accessories
before performing wet cutting operations.
CAUTION:
Be sure to feed water to a wet-type
diamond wheel during wet cutting operations.
Wet cutting with water supply tank
CAUTION:
Avoid filling the water supply tank
with unclean water, such as muddy water, or else
the water outlet will be blocked resulting in dam-
age to the tool.
NOTICE:
Be sure to drain out water from the water
supply tank completely after each use.
1. Open the lid-cap of the water supply tank, and fill
the tank with water. Then set the water-filled tank in the
water supply holder of the tool.
► Fig.29: 1. Lid-cap
2. Hold the tool firmly. Set the base plate on the
workpiece to be cut without the diamond wheel making
any contact.
► Fig.30
3. Start feeding water to the diamond wheel by pull-
ing the water supply lever towards the "ON" (I) position.
Water flow can be adjusted by moving the water supply
lever. Turn the lever to the "ON" (I) position to increase
flow, and to the "OFF" (O) position to reduce flow.
► Fig.31: 1. Water supply lever 2. "ON" (I) position
3. "OFF" (O) position
4. Turn the tool on and wait until the diamond wheel
attains full speed. Then move the tool forward over
the workpiece surface, keeping it flat and advancing
smoothly until the cutting is completed.
5. Having finished operation, be sure to set the lever
in the "OFF" (O) position to cut flow off.
Wet cutting with water supply hose
CAUTION:
Always pay attention to the control
of water pressure. Too high water pressure may
cause water leak and splashing.
1. Set the water supply lever in the "ON" (I) position.
► Fig.32: 1. Water supply lever 2. "ON" (I) position
3. "OFF" (O) position
2. Start feeding water to the diamond wheel by
turning the mains water supply on. Water flow can be
adjusted by moving the water supply lever. Turn the
lever to the "ON" (I) position to increase flow, and to the
"OFF" (O) position to reduce flow.
► Fig.33
3. Hold the tool firmly. Set the base plate on the
workpiece to be cut without the diamond wheel making
any contact.
► Fig.34
4.
Turn the tool on and wait until the diamond wheel
attains full speed. Then move the tool forward over
the workpiece surface, keeping it flat and advancing
smoothly until the cutting is completed.
5. Having finished operation, be sure to set the lever
in the "OFF" (O) position to cut flow off and turn the
water off.
17 ENGLISH