Contents English - Bosch SCT Serie Prüfbuch

en en 26 | SCT / CCT / EL |

Contents English

Contents English
1. Symbols used
1.1 In the documentation
1.1.1 Warning notices -
Structure and meaning
1.1.2 Symbols in this documentation
1.2 On the product
2. User instructions
2.1 Test devices
2.1.1 Test template 1 690 385 006
2.1.2 Test board 1 690 382 354
2.1.3 Laser module 1 690 381 124
2.2 Test requirements
2.3 Definition of the angle being checked
2.4 Requirements
3. Overview of calibration and adjustment
devices
3.1 SCT 415 / CCT 3100
3.2 EL 52425 (Opel)
3.3 SCT 416 / CCT 3500
3.4 SCT 141x
3.5 SCT 410
4. Checking standard components
4.1 Checking the precision measuring bar
4.1.1 Checking the L -bracket (also for EL
52425)
4.1.2 Replacing the spirit level for the roll
angle on the L -bracket (also for
EL 52425)
4.1.3 Replacing the spirit level for the pitch
angle on the L -bracket (also for
EL 52425)
4.1.4 Checking the slides on the precision
measuring bar
4.2 Testing the laser module P-Assist S5
1 690 381 124 / 1 690 381 174
4.2.1 Checking the laser beam length
4.2.2 Checking the laser beam width
4.2.3 Checking the P-Assist S5 play
4.2.4 Checking the P-Assist S5 in laser
mount A
4.2.5 Checking the P-Assist S5 in laser
mount B
4.2.6 Checking the P-Assist S5 for rotation 35
4.3 Checking the calibration targets 1 690 382 xxx 37
|
1 690 386 058 2018-01-30
5. Maintenance SCT 415/ SCT 416 / CCT 3100 /
CCT 3500 / EL 52425
27 5.1 Entire unit
27 5.1.1 Checking the roll angle and pitch
angle
27 5.1.2 Checking the pitch angle on the
27 slides
27 5.1.3 Checking the yaw angle (SCT 416 /
CCT 3500 only)
27 5.2 Components
27 5.2.1 Checking the post
27 5.2.2 Slide on the post
28 5.2.3 Base plate
28 5.2.4 Positioning units
28 5.2.5 Adjustment beam
28 5.2.6 Checking the reference boards
28 5.2.7 Checking the alignment lasers
6. Maintenance SCT 141x
29 6.1 Entire unit
29 6.1.1 Checking the pitch angle
29 6.1.2 Checking the yaw angle
30 6.2 Components
30 6.2.1 Checking the end stops
31 6.2.2 Checking the mounts
6.2.3 Checking the position indicator
31 6.2.4 Checking the tape measure holder
31
7. Maintenance SCT 410
32 7.1 Components
7.1.1 Checking the socket pin
7.1.2 Check the angle mounting bracket
32 and clamp
32
33
33
33
33
33
34
35
37
37
37
38
39
41
41
41
41
42
43
43
44
45
45
45
46
46
46
47
47
47
47
47
47
47
Robert Bosch GmbH