Avdel ESN50LAV Bedienungsanleitung Seite 22

Instruction Manual
Riveting tool ESN50LAV
4.3 Service and maintenance instruction
For every day service the tool has to be cleaned and dried
after each use. The battery cartridge and the charging unit
have to be protected against humidity and dust.
Attention
Maintain power tools thoroughly. Check for
functionality or jamming of moving parts,
breakage of parts and any other condition that
may affect the power tools operation.
4.3.1 Service
The tool is equipped with a controller enabling the user to
see when the next service is due by fl ashing for 20 sec.
at the end of a working cycle. When the next service is
due after 10.000 cycles the unit must be returned to an
authorised service center. Failure to observe this request
results in loosing the Warranty. Preventive maintenance
serves your safety. .
Attention
Do not damage the seals of the tool
Attention
Have the power tool repaired by a qualifi ed ex-
pert before use.
4.3.2 Cleaning
Where the tool is used in a environment containing adhe-
sives etc. a method of completely removing such subs-
tances should be employed when cleaning parts. We de-
fer responsibilty to the customer for the choice and safe
use of the solvents or other substances.
Attention
Ensure that there is no debris in the cylinder
area. Metal chips can damage the cylinder walls
and result in leakages.
Attention
Do not cycle tool without rivets and material!
Attention
Clean the threads of the riveting head and cy-
linder area before the assembly/change of the
head.
4.4 Daily Maintenance
Check die for wear, especially on the centre 'pip' on an
•
upsetting die, use a new die for comparison. Clean out
metal deposits.
4.5 Reference as to which spare parts
can be exchanged by the customer
Within the determined use of the tool only the dies
and punches are permitted to be changed by the
customer.
HE.17489_A © 06/2016
5. Troubleshooting
a.) Constant fl ashing/indicating of the red LED or the
occurence of an acoustical warning signal.
see table 2. If the failure can not be solved return

the tool to the nearest service center (ASC).
b.) The tool loses oil.
 Return the unit to the manufacturer. Do not open it
and damage the seal of the tool.
c.) The red LED fl ashes 3x and simultaneously 3
acoustic warning signals occure (see table 2).
 Serious fault! If this fault occures repeatedly return
the unit to an Autorized Service Center (ASC). Do
not open it and damage the seal of the tool.
6. Technical Data
Weight: ESN50LAV: 3,4 kg (incl. battery)
Stroke: see tab. 1
Joining force: approx. 20 - 50 kN
(adjustable)
Downholder force: approx. 20% of the joining force
Battery voltage: 18 V
Battery capacity 3 Ah (RAL2/BL1830)
Charging time: 22 min. (RAL2/BL1830)
Riveting time: 3 - 5 s
Capacity 150 - 300 rivets (depending on the
per battery: force adjustment and riveting size)
Hydraulic oil: Rivolta S.B.H. 11
Environmental -12°C to +40°C
temperature:
Sound level: < 70 dB (A) in 1m distance
Vibrations: < 2,5 m/s²
7. Putting out of operation/waste
disposal
This unit is subjected to the scope of the European WEEE
(2012/19/EU) and RoHS (2011/65/EU) directives.
Information about this can be found on our home page
www.Klauke.com under 'WEEE & RoHS'.
Battery cartridges must be specially disposed of accor-
ding to the EEC Battery Guideline.
Attention
Do not dispose of the unit in your residential
waste. Klauke has no legal obligation to take
care of their WEEE outside Germany unless the
product has been shipped and invoiced from
inside your country by Klauke. Please contact
your distributer to fi nd out more how to get your
tool recycled environmentally friendly.
Note
Additional copies of the of the IM are availab-
le upon request with no charge. The part # is
HE.17489.
3
GB