Rimage Professional 5100N Einrichtungs- Und Installationsanleitung Seite 2

4
Connect the Professional cables
a. Make sure that the main power switch is in the Off position.
b. Connect the power cord from the Professional to a power outlet.
-
Important! Do not power on the Professional until you are
instructed to do so.
c. Connect the network cable to the embedded control center.
Power
Cord
Main Power
Switch
5
Connect a monitor, mouse, and keyboard (optional)
If the system is not attached to a network, you must connect a monitor,
mouse, and keyboard to the appropriate ports on the back of the
Professional. Refer to the image below.
 Note: If this system is on a network, the monitor, mouse and keyboard
are optional. You may also use Remote Desktop Connection to log on
to the system. Refer to step 6.
Mouse
Keyboard
6
Power on the Professional
a. Set the main power
switch at the back of
the Professional to the
On position.
Main Power
Switch
b. Press the embedded
control center
power button on
Embedded Control
the front of the
Center Power
Professional to power Button
on the system.
c. Allow the system to complete initialization.
 Note: Initialization may take up to 5 minutes. When the
Professional completes the initialization, the operator panel
displays [RIMAGE SYSTEM READY].
2000448_E Copyright © 2010 Rimage Corporation
7
Log on
 Note: Rimage recommends that your Network Administrator use these
instructions as a guide to complete the configuration and software
installation.
•
If this system is connected to a network, access is made through Microsoft
Remote Desktop Connection running on a separate PC. See the Rimage
Advanced Setup (Networking) Guide for information on accessing Remote
Desktop Connection.
 Note: If you are accessing the system remotely, you must wait to log on
until the system initialization completes. This may take several minutes.
The Media Bin, Retransfer and Ribbon statuses display repeatedly on
the system operator panel when the system is finished initializing.
Network
Cable
-
Important! If there is more than one Professional on the network, you
must change the computer name. Refer to step 8.
•
If you connected a monitor, keyboard, and mouse, log on to the Professional
with the following information:
User name: Administrator
Password: password (case sensitive)
8
Install the printer driver
The printer driver installs automatically.
 Note: If the New Hardware Wizard displays, follow the prompts to complete
the Wizard and install the printer.
Monitor
9
Change the computer name
-
Important! You must change the computer name if there is more than one
Professional on the network.
a. Access the system through Remote Desktop Connection.
b. From the Windows Start menu, right-click My Computer and select:
Properties > Computer Name tab.

Note: In Windows Vista, select Change settings in the System window.
i. Enter a unique name in the Computer description: field.

Note: The name can be up to 15 characters long.
ii. Select Change. The Computer Name Changes window opens.
•
Enter the same unique name in the Computer name: field.
•
Under the Member of section, select the Workgroup: option button.
•
Enter RimageSystems in the Workgroup: field.

•
Select OK.
iii. Select Apply.
c. Restart the Professional.
 Note: Use the new computer name next time you access this
Professional through Remote Desktop Connection.
Note: If you are adding the Professional to a domain, do not
enter a Workgroup. Instead, refer to the Rimage Advanced
(Networking) Setup Guide.
10
Activate your Rimage Software (for software
version 8.1 or lower only)
You have 30 days to activate your Rimage software. Until your software
is activated, you will be prompted to do so each time you use the Rimage
software.
When the activation dialog displays, select an option and follow the
onscreen prompts to activate your software.

Note: Activation is only required if you are installing Rimage
software version 8.1 or lower. Product registration for systems using
Rimage software version 8.2 and higher is now managed on the
Rimage website at www.rimage.com/support/warranty-registration.
11
Test and verify
Use QuickDisc to run a 3-disc test job to verify that the system operates
correctly. Refer to the Getting Started with Rimage Software.
 Note: If the disc is not centered on the printer tray,or there are
clamping errors, refer to the Align the Printer instructions found in the
Rimage Professional 5100N and 5300N User Guide.
12
Learn more
•
For information about submitting orders to the Professional across a
network, or to view the latest information on remote accessing, refer to
the Advanced Setup (Networking) Guide.
•
For information about operating and maintaining the Professional, refer to
the Rimage Professional 5100N and 5300N User Guide.
•
For additional support and product information, go to
www.rimage.com/support.
Page 2